Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään

NEMIX RAM

NEMIX RAM 8GB DDR4 2933MHz CL21 1Rx8 1.2V 288-pin UDIMM memory upgrade

SKU CH-5MH9-YRQ5R

8GB DDR4 2933MHz CL21 UDIMM module validated for Supermicro X12SCQ and X12SCZ-QF motherboards

  • Capacity8GB
  • Type288-Pin DDR4 UDIMM
  • SpeedDDR4 2933 (PC4 23400)
  • CAS LatencyCL21
  • Voltage1.20V
  • ECCNo
  • Exact-match DDR4-2933 upgrade installs at full rated speed
  • Verified fit for Supermicro X12SCQ and X12SCZ-QF motherboards
  • Major OEM chips from Samsung Micron or Hynix ensure tested stability
  • 20 V operation and CL21 timing match controller expectations
  • 288-pin UDIMM form factor with 1Rx8 rank for correct population

Exact-match DDR4 upgrade

This NEMIX RAM module delivers 8GB of DDR4 2933MHz memory built to the PC4-23400 standard with CL21 latency and 1.2V operation. It uses a 1Rx8 rank configuration on a 288-pin UDIMM form factor and is verified for Supermicro X12SCQ and X12SCZ-QF motherboards.

Verify motherboard population rules

Before ordering, consult your system or motherboard manual for supported capacities, approved DIMM population order, and installation steps. The module is non-ECC and unbuffered, so confirm your board accepts this type and that the rank and voltage match the controller requirements.

Fits standard desktop DIMM slots

The 288-pin UDIMM design installs directly into compatible desktop memory slots without requiring ECC or registered module support. It uses major OEM chips from Samsung, Micron, or Hynix tested at rated speed and timing, freeing you from compatibility guesswork while adding capacity to your existing platform.

Kohokohdat

  • Exact-match DDR4-2933 upgrade installs at full rated speed
  • Verified fit for Supermicro X12SCQ and X12SCZ-QF motherboards
  • Major OEM chips from Samsung Micron or Hynix ensure tested stability
  • 20 V operation and CL21 timing match controller expectations
  • 288-pin UDIMM form factor with 1Rx8 rank for correct population

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR4 Non-ECC Unbuffered UDIMM Memory
Part NumberMD23400-818K1
Capacity8GB
Type288-Pin DDR4 UDIMM
SpeedDDR4 2933 (PC4 23400)
CAS LatencyCL21
Voltage1.20V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR4 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content8GB DDR4 2933MHz PC4-23400 1Rx8 1.2V 288-PIN Non-ECC UDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does the module arrive as a single stick or a kit, and are any extra parts needed for installation?

The package contains one 8GB DDR4 2933MHz UDIMM; no cables, brackets or additional hardware are required for a standard desktop DIMM slot.

Should I pick this 8GB CL21 version or look for a different capacity or latency?

This part is an 8GB single-rank CL21 module validated for Supermicro X12SCQ and X12SCZ-QF boards; choose it when your system manual calls for exactly that capacity, rank and timing.

What does the 2933MHz rating mean once the DIMM is seated in a compatible Supermicro board?

The board's memory controller will recognise the SPD profile and run the module at 2933MHz with CL21 timing at 1.2V, delivering the rated PC4-23400 data rate without manual configuration.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.