Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Twelve green DDR5 RDIMM modules in a row, bare circuit boards with black chips, no heat spreaders

NEMIX RAM

NEMIX RAM 576GB 12x48GB DDR5 4800 CL40 1.1V 2Rx8 ECC RDIMM Supermicro H14DST-F memory upgrade

SKU CH-54YR-J1TTS

A 576GB DDR5-4800 ECC Registered RDIMM kit of twelve 48GB modules at CL40 and 1.1V, validated for the Supermicro H14DST-F motherboard

  • Capacity576GB (12 x 48GB)
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 4800 (PC5 38400)
  • CAS LatencyCL40
  • Voltage1.10V
  • ECCYes

Size 576GB 12X48GB

Näytä 30 muuta kokoonpanoa
  • 576GB total capacity from twelve 48GB modules for maximum server density
  • DDR5 4800 speed with CL40 latency matches the memory controller specification exactly
  • Registered ECC design with 2Rx8 organisation prevents data errors at full population
  • 1V operating voltage meets the platform requirement for stable operation
  • Verified compatibility with Supermicro H14DST-F motherboard ensures correct fit and recognition

576GB DDR5-4800 ECC RDIMM kit

This 576GB kit contains twelve 48GB DDR5-4800 registered ECC modules built to the PC5-38400 standard. Each DIMM runs at 1.1V with CL40 latency and a 2Rx8 organisation. The 288-pin RDIMM form factor is the exact type required by the Supermicro H14DST-F motherboard.

Suited for fully populated H14DST-F servers

Administrators expanding a Supermicro H14DST-F to its maximum supported capacity with registered ECC memory will find the correct rank, voltage and timing in this kit. Builders who need unbuffered UDIMMs, SODIMMs, non-ECC modules or a different DDR generation cannot use these DIMMs.

12-module population requirement

The kit delivers 576GB only when all twelve slots are filled with the supplied 48GB RDIMMs. Partial population will not yield the stated capacity and may violate the motherboard's memory-population rules.

Kohokohdat

  • 576GB total capacity from twelve 48GB modules for maximum server density
  • DDR5 4800 speed with CL40 latency matches the memory controller specification exactly
  • Registered ECC design with 2Rx8 organisation prevents data errors at full population
  • 1V operating voltage meets the platform requirement for stable operation
  • Verified compatibility with Supermicro H14DST-F motherboard ensures correct fit and recognition

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR38400-4828K12
Capacity576GB (12 x 48GB)
Type288-Pin DDR5 RDIMM
SpeedDDR5 4800 (PC5 38400)
CAS LatencyCL40
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content576GB 12X48GB DDR5 4800MHz PC5-38400 2Rx8 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does the Supermicro H14DST-F need all 12 slots filled for this 576GB kit to operate?

The H14DST-F has 12 DDR5 RDIMM slots; populating every slot with the 12x48GB modules delivers the full 576GB at DDR5-4800, but the board will also run with fewer modules installed following its population order.

Can I mix these 48GB 2Rx8 DDR5-4800 RDIMMs with smaller DDR5 RDIMMs already in the server?

Mixing different capacities or ranks is possible if the motherboard's population rules allow it, though the memory controller will run all modules at the lowest common speed and timing.

How do I confirm the kit is running at DDR5-4800 CL40 1.1V after installation?

Check the BIOS memory information or a tool such as dmidecode; it should show each DIMM at 4800 MT/s, CAS 40, 1.1V, and the total capacity at 576GB with ECC active.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.