Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green DDR5 RDIMM modules with black chips and gold contacts, no heat spreader

NEMIX RAM

NEMIX RAM 64GB 2x32GB DDR5 5600 CL46 1.1V 2Rx8 ECC Registered RDIMM Kit for Supermicro H14SSF memory upgrade

SKU CH-BTPA-6HWG6

64 GB dual-rank DDR5 registered ECC kit runs at 5600 MT/s with CL46 timing and 1.1 V for the Supermicro H14SSF motherboard

  • Capacity64GB (2 x 32GB)
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 64GB 2X32GB

Näytä 24 muuta kokoonpanoa
  • 64 GB capacity from a matched 2 × 32 GB kit for full server density
  • DDR5 5600 speed with CL46 latency runs at rated performance
  • 1 V operation lowers power draw per module
  • Registered ECC RDIMM corrects single-bit errors and buffers the memory bus
  • 288-pin form factor fits the Supermicro H14SSF motherboard exactly

Exact DDR5 RDIMM kit for Supermicro H14SSF

This 64 GB kit contains two 32 GB DDR5 5600 RDIMMs built to the exact rank, voltage and timing the H14SSF memory controller expects. Registered ECC architecture with CL46 latency and 1.1 V operation ensures the modules are recognised at full capacity and run at rated speed without manual tuning.

DDR5 5600 registered ECC limits

DDR5 5600 (PC5-44800) registered DIMMs require a motherboard that supports registered signalling and ECC correction; consumer boards that accept only unbuffered UDIMMs will not post with these modules. The 2Rx8 organisation and 1.1 V spec must match the platform's qualified-vendor list, otherwise the system may down-clock or refuse to boot.

Straightforward server DIMM installation

Power down the server, open the chassis and align each 288-pin module with the keyed slot following the motherboard's population order. Press firmly until both retention clips latch; a common mistake is seating only one side, which causes a memory error at POST. Verify the BIOS reports 64 GB at DDR5 5600 before closing the case.

Kohokohdat

  • 64 GB capacity from a matched 2 × 32 GB kit for full server density
  • DDR5 5600 speed with CL46 latency runs at rated performance
  • 1 V operation lowers power draw per module
  • Registered ECC RDIMM corrects single-bit errors and buffers the memory bus
  • 288-pin form factor fits the Supermicro H14SSF motherboard exactly

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-328K2
Capacity64GB (2 x 32GB)
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content64GB 2X32GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Is this 64GB 2x32GB DDR5 5600 kit the right capacity for my Supermicro H14SSF?

The kit provides 64GB total as two 32GB modules, matching the board's DDR5 RDIMM slot requirements; verify your manual for maximum supported capacity and approved population order before installing.

Will the DDR5 5600 CL46 speed run at full rate on the H14SSF?

The modules are spec-matched to the board's memory controller at 5600 MT/s with CL46 latency and 1.1V, so the system recognises them at rated speed when populated per the manufacturer's guidelines.

Does the 288-pin Registered ECC RDIMM form factor fit the H14SSF slots?

Yes, the 288-pin DDR5 RDIMM is the exact form factor the H14SSF requires; registered architecture and on-die ECC let every slot run fully populated while correcting single-bit errors.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.