NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
NEMIX RAM
8GB DDR4 2666 ECC UDIMM CL19 1.2V 2Rx8 288-pin server memory for compatible NAS and workstations
This 8 GB DDR4 ECC unbuffered DIMM runs at 2666 MHz with CL19 latency and 1.20 V operation. It is built for QNAP NAS devices that accept 288-pin UDIMM modules and require error-correcting memory for data integrity. The 2Rx8 organisation uses major OEM chips from Samsung, Micron or Hynix.
Operating at the standard 1.20 V for DDR4, the module draws minimal power and generates low heat without a heat spreader. Passive airflow inside a typical NAS chassis is sufficient to keep temperatures in check during continuous operation. No active cooling or extra voltage headroom is needed for stock-speed workloads.
ECC support detects and corrects single-bit errors, protecting stored data from silent corruption in always-on NAS environments. The unbuffered design keeps latency low for the memory controller while the 2Rx8 layout fits the density limits of compatible QNAP models. No additional software or drivers are required beyond the NAS firmware.
| Brand | NEMIX RAM |
|---|---|
| Series | QNAP NAS Device Memory |
| Model | QNAP NAS Memory |
| Part Number | ME21300-828K1 |
| Capacity | 8GB |
| Type | 288-Pin DDR4 ECC UDIMM |
| Speed | DDR4 2666 (PC4 21300) |
| CAS Latency | CL19 |
| Voltage | 1.20V |
| ECC | Yes |
| Buffered/Registered | Unbuffered |
| Rank | 2Rx8 |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Heat Spreader | No |
| Features | DDR4 ECC Unbuffered UDIMM Motherboard Compatible |
Align the notch on the 288-pin module with the slot key, press firmly until both retention clips click, then verify the system reports 8 GB at 2666 MT/s in the NAS firmware — the step most often missed is reseating if the POST does not show the new capacity.
No scheduled maintenance is required; the module has no heat spreader and runs at 1.20 V, so only replace it if memory diagnostics report uncorrectable ECC errors or if you expand capacity beyond the current 8 GB.
The CAS latency of 19 cycles at 2666 MT/s sets the throughput ceiling; under continuous load the memory controller will hit that timing boundary before voltage or thermal limits become a factor.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?