Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.

Prisvagt Log ind
Green rectangular circuit board with gold edge connectors and black memory chips visible

NEMIX RAM

NEMIX RAM 8GB DDR4 2666 ECC UDIMM CL19 1.2V 2Rx8

SKU CH-N613-D3Z61

8GB DDR4 2666 ECC UDIMM CL19 1.2V 2Rx8 288-pin server memory for compatible NAS and workstations

  • Capacity8GB
  • Type288-Pin DDR4 ECC UDIMM
  • SpeedDDR4 2666 (PC4 21300)
  • CAS LatencyCL19
  • Voltage1.20V
  • ECCYes
  • ECC protection guards data integrity with built-in error correction
  • DDR4 2666 speed delivers responsive performance for server workloads
  • Low 1.20V operation reduces power draw and heat output
  • 2Rx8 dual-rank layout boosts memory bandwidth on compatible boards
  • 288-pin UDIMM form factor fits standard DDR4 server slots

8GB DDR4 ECC UDIMM for QNAP NAS

This 8 GB DDR4 ECC unbuffered DIMM runs at 2666 MHz with CL19 latency and 1.20 V operation. It is built for QNAP NAS devices that accept 288-pin UDIMM modules and require error-correcting memory for data integrity. The 2Rx8 organisation uses major OEM chips from Samsung, Micron or Hynix.

Thermals and power in normal use

Operating at the standard 1.20 V for DDR4, the module draws minimal power and generates low heat without a heat spreader. Passive airflow inside a typical NAS chassis is sufficient to keep temperatures in check during continuous operation. No active cooling or extra voltage headroom is needed for stock-speed workloads.

What the bundled specs change

ECC support detects and corrects single-bit errors, protecting stored data from silent corruption in always-on NAS environments. The unbuffered design keeps latency low for the memory controller while the 2Rx8 layout fits the density limits of compatible QNAP models. No additional software or drivers are required beyond the NAS firmware.

Fordele

  • ECC protection guards data integrity with built-in error correction
  • DDR4 2666 speed delivers responsive performance for server workloads
  • Low 1.20V operation reduces power draw and heat output
  • 2Rx8 dual-rank layout boosts memory bandwidth on compatible boards
  • 288-pin UDIMM form factor fits standard DDR4 server slots

Specifikationer

BrandNEMIX RAM
SeriesQNAP NAS Device Memory
ModelQNAP NAS Memory
Part NumberME21300-828K1
Capacity8GB
Type288-Pin DDR4 ECC UDIMM
SpeedDDR4 2666 (PC4 21300)
CAS LatencyCL19
Voltage1.20V
ECCYes
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
FeaturesDDR4 ECC Unbuffered UDIMM Motherboard Compatible

Spørgsmål om denne vare

How do I install this DDR4 ECC UDIMM in my QNAP NAS and what step is often missed?

Align the notch on the 288-pin module with the slot key, press firmly until both retention clips click, then verify the system reports 8 GB at 2666 MT/s in the NAS firmware — the step most often missed is reseating if the POST does not show the new capacity.

What maintenance or replacement will this 2Rx8 module need over time?

No scheduled maintenance is required; the module has no heat spreader and runs at 1.20 V, so only replace it if memory diagnostics report uncorrectable ECC errors or if you expand capacity beyond the current 8 GB.

What limit appears first when this CL19 kit runs sustained workloads?

The CAS latency of 19 cycles at 2666 MT/s sets the throughput ceiling; under continuous load the memory controller will hit that timing boundary before voltage or thermal limits become a factor.

Også på denne hylde

Kunderne har også sammenlignet disse

Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.