Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green DDR5 RDIMM modules with black chips and gold contacts

NEMIX RAM

NEMIX RAM DDR5 5600 192GB (2x96GB) ECC RDIMM Supermicro X14SDV-32C-SP3F

SKU CH-GEWM-MH7T5

192 GB DDR5-5600 ECC registered RDIMM kit (2×96 GB, CL46, 1.1 V) validated for Supermicro X14SDV-32C-SP3F motherboards

  • Capacity192GB (2 x 96GB)
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 192GB 2X96GB

  • 192 GB total capacity from two 96 GB modules for high-density server workloads
  • DDR5 5600 speed with CL46 latency delivers rated throughput on supported platforms
  • Registered ECC architecture corrects single-bit errors and enables full-slot population
  • 1 V operating voltage matches DDR5 standard for efficient power draw
  • Verified compatibility with Supermicro X14SDV-32C-SP3F motherboard ensures proper fit and recognition

Exact-Match Upgrade

This 192GB kit delivers two 96GB DDR5 5600 registered ECC RDIMMs built for the Supermicro X14SDV-32C-SP3F motherboard. The modules run at 1.1V with CL46 timing and a 2Rx4 rank structure that matches the board's memory controller requirements. Registered buffering lets every slot operate at full capacity without signal degradation. ECC corrects single-bit errors on the fly to prevent silent data corruption.

Replaces Partial Or Mismatched Kits

Servers running with smaller RDIMMs, unbuffered UDIMMs, or mixed-rank configurations can move to this spec-matched 192GB set to regain full-channel bandwidth and population-rule compliance. The upgrade is worth it when the workload demands maximum registered capacity per slot and the motherboard manual confirms support for 96GB 2Rx4 modules at DDR5-5600. Systems limited to lower densities or different rank layouts will not benefit.

Straightforward Slot Installation

Align the 288-pin key, press evenly until the latches click, and follow the board's prescribed population sequence for 2Rx4 registered DIMMs. The most common issues are ignoring the manual's slot order, mixing ranks within a channel, or seating a module slightly off-centre so the register does not initialise. No heat spreader is present, so handle the bare PCB by the edges and avoid static discharge.

Kohokohdat

  • 192 GB total capacity from two 96 GB modules for high-density server workloads
  • DDR5 5600 speed with CL46 latency delivers rated throughput on supported platforms
  • Registered ECC architecture corrects single-bit errors and enables full-slot population
  • 1 V operating voltage matches DDR5 standard for efficient power draw
  • Verified compatibility with Supermicro X14SDV-32C-SP3F motherboard ensures proper fit and recognition

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-9624K2
Capacity192GB (2 x 96GB)
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx4
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content192GB 2X96GB DDR5 5600MHz PC5-44800 2Rx4 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Will these 288-pin DDR5 RDIMMs fit the Supermicro X14SDV-32C-SP3F motherboard slots?

Yes, the kit is built as 288-pin DDR5 Registered DIMMs, the exact form factor the X14SDV-32C-SP3F requires; UDIMM or SODIMM modules will not seat in these slots.

What population order should I follow when installing the two 96GB modules on this board?

Consult the Supermicro X14SDV-32C-SP3F manual for the approved DIMM population sequence; the board's memory-controller rules dictate which slots must be filled first for full 192GB recognition at DDR5-5600.

Do these registered ECC modules need any firmware updates or periodic reconfiguration after installation?

No firmware updates or reconfiguration are required; the Registered ECC design handles error correction automatically, and the modules run at the rated 1.1V CL46 timings for their service life.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.