Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green bare circuit board 288 pin DDR5 RDIMM memory module no heat spreader

NEMIX RAM

NEMIX RAM DDR5 5600 96GB ECC RDIMM 2Rx4 CL46 1.1V GIGABYTE MZ73-LM2 memory upgrade

SKU CH-6NCD-024QK

96GB DDR5-5600 registered ECC RDIMM with CL46 latency and 1.1V operation, built for the GIGABYTE MZ73-LM2 motherboard

  • Capacity96GB
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 96GB

Näytä 24 muuta kokoonpanoa
  • 96 GB capacity lets your GIGABYTE MZ73-LM2 handle large workloads without swapping
  • DDR5 5600 speed delivers PC5-44800 bandwidth for data-intensive applications
  • ECC and registered design correct single-bit errors and reduce controller load in fully populated servers
  • CL46 latency at 1.1 V balances responsive timing with efficient power use
  • 288-pin 2Rx4 RDIMM form factor matches the board's exact slot and population requirements

96GB DDR5 ECC RDIMM for GIGABYTE MZ73-LM2

This 96GB DDR5-5600 registered ECC module is built for the GIGABYTE MZ73-LM2 motherboard. It delivers the exact rank, voltage and timing the board's memory controller expects so the full capacity is recognised at rated speed. It suits administrators upgrading or repairing that specific server platform.

Registered 288-pin form factor

The registered architecture buffers address and command signals, letting every slot run fully populated without overloading the memory controller. ECC corrects single-bit errors on the fly to prevent silent data corruption and unplanned reboots. The 288-pin RDIMM keying fits only boards wired for registered DDR5; it will not work in UDIMM or SODIMM slots.

CL46 at 1.1V defines the compatibility window

The module operates at CL46 latency and 1.1V, matching the JEDEC DDR5-5600 (PC5-44800) specification the MZ73-LM2 requires. If your board demands different timings, voltages or a non-registered layout, this kit will not post or will down-clock. Verify the manual's approved DIMM population order before purchase.

Kohokohdat

  • 96 GB capacity lets your GIGABYTE MZ73-LM2 handle large workloads without swapping
  • DDR5 5600 speed delivers PC5-44800 bandwidth for data-intensive applications
  • ECC and registered design correct single-bit errors and reduce controller load in fully populated servers
  • CL46 latency at 1.1 V balances responsive timing with efficient power use
  • 288-pin 2Rx4 RDIMM form factor matches the board's exact slot and population requirements

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-9624K1
Capacity96GB
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx4
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemGIGABYTE
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content96GB DDR5 5600MHz PC5-44800 2Rx4 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does the DDR5 5600 PC5-44800 interface cap the module at 5600 MT/s even if the board supports faster speeds?

Yes, the module is rated at 5600 MT/s (PC5-44800) with CL46 latency and 1.1 V, so it will run at that speed unless the platform downclocks it.

Will the 288-pin ECC Registered RDIMM fit the GIGABYTE MZ73-LM2 motherboard DIMM slots?

The 288-pin RDIMM form factor matches the MZ73-LM2's registered DIMM slots; UDIMM or SODIMM modules will not fit.

What is the correct installation step for the 2Rx4 registered ECC kit on the MZ73-LM2?

Follow the motherboard manual's population order for registered DIMMs; the common mistake is inserting modules in the wrong slot sequence for the specific CPU configuration.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.