Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään

NEMIX RAM

NEMIX RAM MD25600-818K2 16GB 2x8GB DDR4 3200 CL22 Supermicro X12STE-F X12STD-F memory upgrade

SKU CH-8FVP-52EGQ

16 GB DDR4 3200 kit with two 8 GB UDIMMs validated for Supermicro X12STE-F and X12STD-F motherboards

  • Capacity16GB (2 x 8GB)
  • Type288-Pin DDR4 UDIMM
  • SpeedDDR4 3200 (PC4 25600)
  • CAS LatencyCL22
  • Voltage1.20V
  • ECCNo
  • Ready for Supermicro X12STE-F and X12STD-F boards
  • 16 GB dual-channel kit runs at DDR4 3200 CL22
  • 2 V unbuffered UDIMM keeps power draw low
  • Major OEM chips tested for stability at rated speed
  • 288-pin 1Rx8 layout matches motherboard memory rules

Targeted DDR4 upgrade

This 16 GB kit contains two 8 GB DDR4-3200 UDIMMs built to the exact rank, voltage and timing the Supermicro X12STE-F and X12STD-F motherboards expect. The modules are non-ECC, unbuffered and run at 1.2 V with CL22 latency. They install in the standard 288-pin desktop slots and are validated for full-speed recognition on those boards.

Fitment guidance

Builders upgrading a compatible Supermicro workstation or server board will get plug-and-play capacity without BIOS guesswork. Buyers who need ECC error correction, registered modules or SODIMM form factors must look elsewhere because this kit is strictly non-ECC unbuffered UDIMM. Systems that require a different voltage, pin count or memory generation are also not supported.

Sustained operation

Major OEM chips from Samsung, Micron or Hynix are tested for stability at the rated 3200 MT/s speed and CL22 timing under continuous load. The 1Rx8 organisation and 1.2 V operation keep power draw consistent during extended workloads. No heat spreader is fitted, so adequate chassis airflow is required to maintain the specified performance over long sessions.

Kohokohdat

  • Ready for Supermicro X12STE-F and X12STD-F boards
  • 16 GB dual-channel kit runs at DDR4 3200 CL22
  • 2 V unbuffered UDIMM keeps power draw low
  • Major OEM chips tested for stability at rated speed
  • 288-pin 1Rx8 layout matches motherboard memory rules

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR4 Non-ECC Unbuffered UDIMM Memory
Part NumberMD25600-818K2
Capacity16GB (2 x 8GB)
Type288-Pin DDR4 UDIMM
SpeedDDR4 3200 (PC4 25600)
CAS LatencyCL22
Voltage1.20V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR4 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content16GB 2X8GB DDR4 3200MHz PC4-25600 1Rx8 1.2V 288-PIN Non-ECC UDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

What motherboard must I already own for this MD25600-818K2 kit to work?

The kit is validated for Supermicro X12STE-F and X12STD-F motherboards that accept 288-pin DDR4 UDIMMs running at 1.20 V.

How does this 1Rx8 Non-ECC DDR4-3200 kit behave alongside older DDR4 modules I keep installed?

When mixed with slower DDR4 DIMMs the memory controller will down-clock the whole array to the lowest common speed and loosest latency.

How can I confirm the 16 GB kit is running at its rated DDR4-3200 CL22 1.20 V after setup?

Open the BIOS or a tool such as CPU-Z and verify the memory tab shows 3200 MT/s, CL22 timings and 1.20 V on both 8 GB modules.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.