NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
OWC
8GB DDR4 3200 ECC registered RDIMM for server and workstation upgrades
This 8 GB DDR4 3200 module is built for workstations and servers that require registered ECC memory. It operates at PC4-25600 with a CL22 latency and runs at 1.2 V. The single-rank 1Rx8 design fits standard 288-pin RDIMM slots in compatible enterprise platforms.
The module follows JEDEC and RoHS standards without a heat spreader, keeping the profile low for dense server chassis. Registered buffering reduces electrical load on the memory controller, allowing larger total capacities in supported systems. ECC circuitry detects and corrects single-bit errors to protect data integrity.
This memory will not work in standard desktop computers or laptops that use unbuffered non-ECC DIMMs. It cannot be mixed with unbuffered modules in the same system. Check your motherboard or NAS documentation to confirm it accepts DDR4 3200 registered ECC RDIMMs before ordering.
| Brand | OWC |
|---|---|
| Part Number | 3R2D41R808GB |
| Capacity | 8GB |
| Type | 288-Pin DDR4 ECC RDIMM |
| Speed | DDR4 3200 (PC4 25600) |
| CAS Latency | CL22 |
| Voltage | 1.2V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 1Rx8 |
| Heat Spreader | No |
The module runs at 3200 MT/s with CL22 timing; ECC and registered operation add one cycle of buffering, so sustained bandwidth is limited by the JEDEC PC4-25600 rating rather than raw frequency alone
It fits a standard 288-pin DDR4 DIMM socket; no heat spreader is present, so low-profile heatsinks or tight server chassis lids will not interfere with the bare PCB
Power down, open the retention clips, align the single key notch, press firmly until both clips snap shut, then verify in BIOS that ECC and registered modes are enabled — the missed step is confirming the memory mode after boot
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?