Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Orange silk PLA filament on a plastic spool

PrintOxe

PrintOxe PLA like SILK Orange 1.75 mm 1 kg 3D printer filament

SKU CH-042G-XS8BS

1.75 mm orange PLA silk filament on a 1 kg vacuum-sealed spool with ±.03 mm accuracy, printing at 200-220 °C for a high-gloss finish

  • ColorOrange
  • TypeFilament

Color Orange

  • Blue
  • Green
  • Purple
  • Red
  • Silver
  • White
  • Yellow
  • Orange
  • Copper

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Silk-like glossy finish from PLA silk formulation
  • Precise 1.75 mm diameter with ± .03 mm accuracy
  • Low-warp, clog-free printing using 100 % high-purity corn-starch material
  • Vacuum-sealed 1 kg spool with desiccant for moisture protection
  • Wide printer compatibility at 200 °C – 220 °C nozzle temperature

PrintOxe Silk Orange Filament 1.75 mm

This 1 kg spool delivers a high-gloss silk finish on every print. The material is a PLA blend made from corn starch and is non-toxic. Dimensional accuracy is held to ±0.03 mm for consistent extrusion. It suits makers who want shiny, decorative parts without post-processing.

Check printer temperature and spool fit

Verify that your hot end can reach 200 °C to 220 °C for reliable flow. The spool measures 7.88 inches in diameter and 2.69 inches wide with a 2.20 inch centre hole. Ensure your holder accommodates these dimensions before ordering. Vacuum-sealed packaging with desiccant keeps the filament dry until use.

Stable output during long prints

The tight diameter tolerance reduces the risk of clogging or blistering over extended runs. Low shrinkage and minimal warping keep layers aligned on large models. Consistent gloss is maintained from the first layer to the last. Makers needing a matte surface or higher heat resistance should choose a different filament type.

Kohokohdat

  • Silk-like glossy finish from PLA silk formulation
  • Precise 1.75 mm diameter with ± .03 mm accuracy
  • Low-warp, clog-free printing using 100 % high-purity corn-starch material
  • Vacuum-sealed 1 kg spool with desiccant for moisture protection
  • Wide printer compatibility at 200 °C – 220 °C nozzle temperature

Tekniset tiedot

BrandPrintOxe
ModelPLA like SILK
ColorOrange
TypeFilament

Kysymyksiä tästä tuotteesta

Does the 1 kg spool include anything besides the filament itself?

The 1 kg net filament arrives vacuum-sealed with desiccant inside a retail box; no tools or adhesives are included.

Is the 1.75 mm diameter the only size offered for this Silk Orange PLA?

The listed product is 1.75 mm diameter with ±0.03 mm accuracy; no other diameters are mentioned for this variant.

What nozzle temperature range should I set for the recommended 200 °C to 220 °C extrusion window?

Set the hot-end between 200 °C and 220 °C (392 °F to 428 °F) for reliable flow and the advertised silk finish.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.