Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Ten Molex to dual 15-pin SATA power adapter cables in bulk pack

SMUGDESK

SMUGDESK 10-Pack 4-Pin Molex to Dual 15-Pin SATA Power Adapter Cord Convert SSD Optical Drives

SKU CH-8Y3S-QNV61

Ten-piece pack splits one Molex connector into dual SATA power ports for SSDs, HDDs and optical drives

  • Bulk 10-pack keeps repair shops and builders stocked with spare adapters
  • One 4-pin Molex connector splits into two 15-pin SATA power ports
  • Powers two SATA SSDs, HDDs or optical drives from a single legacy supply lead
  • Copper wiring maintains steady current and reduces voltage drop under load
  • Passive plug-and-play design works inside any desktop chassis without drivers

Bulk adapter pack for PC builders

This ten-piece set converts a single four-pin Molex connector into two fifteen-pin SATA power ports. It targets repair shops, DIY assemblers and anyone adding multiple SATA drives to a desktop chassis. No drivers or software are required for installation.

Steady power delivery under load

High-conductivity copper wiring maintains stable current and reduces voltage drop while both connected drives operate simultaneously. The passive splitter relies on the host power supply's rated capacity, so total device draw must stay within that limit to avoid overload.

Simple plug-and-play fitting

Connect the Molex end to the power supply and attach each SATA plug to a drive; the cables seat with a firm click. Common issues arise when the source connector is already heavily loaded or when SATA data cables are forgotten, as they are not included in the pack.

Kohokohdat

  • Bulk 10-pack keeps repair shops and builders stocked with spare adapters
  • One 4-pin Molex connector splits into two 15-pin SATA power ports
  • Powers two SATA SSDs, HDDs or optical drives from a single legacy supply lead
  • Copper wiring maintains steady current and reduces voltage drop under load
  • Passive plug-and-play design works inside any desktop chassis without drivers

Tekniset tiedot

Tälle tuotteelle ei ole vielä julkaistu teknisiä tietoja.

Kysymyksiä tästä tuotteesta

Will the 15-pin SATA connectors run hot when powering drives continuously from one Molex source?

The adapter uses high-conductivity copper wiring to maintain steady current and reduce voltage drop, so heat stays low under normal working load.

What must my power supply already have to use these 4-pin Molex to dual 15-pin SATA adapters?

Your power supply needs an available 4-pin IDE Molex connector; you also need SATA data cables for each drive, which are not included.

Can I keep my older 4-pin Molex power supply while adding modern SATA SSDs with this 10-pack?

Yes, each adapter converts one legacy Molex connector into two 15-pin SATA power ports so you can run SATA drives on older PSUs.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.