Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Square 60mm server fan with blue mounting bracket and four-wire connector

SXDOOL

SXDOOL 2B06038B12G 60mm 12V 2.20A 4-wire ball bearing 14500 RPM case fan

SKU CH-JEBV-FST67 MPN 2B06038B12G

60 mm 12 V ball-bearing fan with 4-wire PWM control spins at 14500 RPM and includes a blue mounting bracket

  • High-speed cooling at 14500 RPM for dense server chassis
  • Four-wire PWM control enables precise automatic speed regulation
  • Ball-bearing design extends operational lifespan under continuous load
  • Direct replacement for HP DL180 G6 G7 part numbers 519199-001 and 530748-001
  • Compact 60 x 60 x 38 mm frame fits restricted 1U bays

Server-grade 60mm replacement fan

This 60mm case fan is built as a direct replacement for HP DL180 G6 and G7 servers as well as the P4300 G2 storage array. It matches the original AVC 2B06038B12G specification and ships with the blue mounting bracket attached. The four-wire connector provides PWM control and tachometer feedback to the server management subsystem. System administrators maintaining these platforms can install it without adapter cables or bracket modifications.

14500 RPM airflow at 12V 2.20A

The fan draws 2.20A at 12V to spin its ball-bearing rotor at 14500 RPM, delivering the high static pressure required by dense 1U and 2U chassis. That speed satisfies the cooling curve of the DL180 G6 and G7 under full CPU and memory load. Headroom diminishes if the chassis air path is obstructed by missing baffles or clogged filters, so the fan cannot compensate for poor rack hygiene or removed airflow guides.

Ball bearing durability and keyed four-wire plug

The ball bearing is rated for continuous operation in server environments where sleeve bearings would wear prematurely. The moulded blue bracket aligns with the original screw holes in the DL180 and P4300 G2 fan trays, preventing vibration-induced noise. The keyed four-wire plug ensures correct polarity and PWM signalling; forcing a three-wire header would disable speed reporting and fan-fault alerts.

Kohokohdat

  • High-speed cooling at 14500 RPM for dense server chassis
  • Four-wire PWM control enables precise automatic speed regulation
  • Ball-bearing design extends operational lifespan under continuous load
  • Direct replacement for HP DL180 G6 G7 part numbers 519199-001 and 530748-001
  • Compact 60 x 60 x 38 mm frame fits restricted 1U bays

Tekniset tiedot

Tälle tuotteelle ei ole vielä julkaistu teknisiä tietoja.

Kysymyksiä tästä tuotteesta

Will the 4-wire plug and 60mm frame fit the existing fan header and mounting holes on my HP DL180 G6?

The fan uses the original 4-wire plug and 60mm x 60mm frame specified for the HP DL180 G6 and G7, so it connects directly to the server's fan header and aligns with the standard mounting points.

How can I verify the 14500 RPM ball-bearing fan is spinning correctly after installation?

The 4-wire connector provides a tachometer signal; monitor the reported speed in the server's BIOS, iLO interface or operating-system hardware monitor and confirm it reads near 14500 RPM under load.

Does the package include the blue mounting bracket shown for the HP DL180 G6, or must I source it separately?

The supplied unit comes with the blue bracket attached, matching the HP 519199-001 and 530748-001 assembly, so no separate bracket purchase is required.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.