Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black 80mm square case fan with hydraulic bearing and three-pin connector

SXDOOL

SXDOOL JF0825S1SA-R 80mm case fan 12V 0.26A 3500 RPM 60 CFM 32 dBA hydraulic bearing 3-pin

SKU CH-DSZC-WX1FP MPN JF0825S1SA-R

An 80 mm hydraulic-bearing case fan delivering 60 CFM at 3500 RPM with 32 dBA noise on a 3-pin 12 V connector

  • Fan Size80mm
  • Bearing TypeHydraulic
  • RPM3500-3999 RPM
  • Air Flow60-65 CFM
  • Noise Level30 - 35 dBA
  • Power Connector4 Pin
  • Moves 60 CFM of air for effective case cooling
  • Hydraulic bearing runs at 32 dBA for quiet operation
  • 3500 RPM speed delivers strong airflow performance
  • 12 V 0.26 A design fits standard 3-pin headers
  • 80 mm frame suits compact builds and UPS units

80 mm hydraulic fan for UPS and compact builds

The SXDOOL JF0825S1SA-R is an 80 mm case fan built around a hydraulic bearing for long service life. It runs on 12 V at 0.26 A and connects via a 3-pin power connector. The black non-LED frame suits UPS units such as Castle series C1K C2K C3K and Shante power supplies as well as small-form-factor enclosures.

Thermals noise and power in normal use

At 3500 RPM the fan moves 60 CFM while producing 32 dBA of noise. The specifications allow a speed range up to 3999 RPM with airflow reaching 65 CFM and noise up to 35 dBA. Power draw stays at 0.26 A on the 12 V rail. The hydraulic bearing keeps friction low for consistent acoustic output.

Replaces worn 80 mm UPS fans when original units

This unit is a direct drop-in for a failed JAMICON JF0825S1SA-R in the listed UPS models. The jump is worth it when the original fan develops bearing noise or stops spinning. It is not for builders who need PWM speed control via a 4-pin header or who require higher static pressure for dense radiator stacks.

Kohokohdat

  • Moves 60 CFM of air for effective case cooling
  • Hydraulic bearing runs at 32 dBA for quiet operation
  • 3500 RPM speed delivers strong airflow performance
  • 12 V 0.26 A design fits standard 3-pin headers
  • 80 mm frame suits compact builds and UPS units

Tekniset tiedot

Fan Size80mm
Bearing TypeHydraulic
RPM3500-3999 RPM
Air Flow60-65 CFM
Noise Level30 - 35 dBA
Power Connector4 Pin
ColorBlack
LEDNon-LED

Kysymyksiä tästä tuotteesta

How do I install the 3-pin connector on this 80 mm fan, and what step do people often miss?

Align the three pins with the motherboard or UPS header, press straight down until the latch clicks, and verify the keyed tab matches the socket notch so the yellow tachometer wire is not shifted one pin over.

What maintenance will the hydraulic bearing need later?

The hydraulic bearing is sealed and requires no lubrication; if noise rises above the rated 32 dBA or speed drops below 3500 RPM, replace the entire fan.

At what point does the 32 dBA noise level become the limiting factor during sustained use?

Under continuous load the fan runs at 3500 RPM producing 32 dBA; if the system demands higher airflow the noise will rise toward 35 dBA before thermal limits are reached.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.