Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Ten red filament spools in a pack, 2.85mm diameter

Taulman 3D

Taulman 3D t-glase Filament 2.85mm Red 10 pack 3D Printers Accessories

SKU CH-2FMX-D4KWF

A 10-spool pack of 2.85 mm PET co-polymer filament formulated for food-safe containers, very low shrinkage on large flat prints, and strength exceeding ABS

  • ColorRed
  • TypeFilament
  • Food-safe polymer approved for direct contact containers
  • Ten spools in one case for high-volume printing
  • Very low shrinkage keeps large flat prints dimensionally accurate
  • Stronger than ABS for durable functional parts
  • Glass-like clarity achievable with optical coatings

Ten-spool pack for high-volume printing

This pack contains ten 1 lb spools of Taulman 3D t-glase filament in red, giving a total of 10 lbs of material. The 2.85 mm diameter suits printers that accept this standard size. The co-polymer is formulated for direct food contact, making it suitable for containers and kitchen items. It is intended for makers who run repeated or large-format jobs and want a consistent supply.

Low shrinkage and industrial strength

The filament exhibits very low shrinkage, which keeps large flat surfaces dimensionally stable during printing. Its tensile strength exceeds that of ABS, a property inherited from Taulman's industrial product line. Optical clarity can approach a glass-like finish when post-processed with appropriate coatings. The material prints reliably on acrylic, glass, Kapton or similar platforms even without a heated bed.

Check printer compatibility and workflow

Verify that your extruder and hot-end accept 2.85 mm filament and can maintain a nozzle temperature between 235 °C and 245 °C. The supplier notes that t-glase prints more slowly than standard PLA or ABS, so it is recommended for intermediate users who can tune speeds and flow rates. Ensure your slicer profile accommodates the material's specific thermal behaviour.

Kohokohdat

  • Food-safe polymer approved for direct contact containers
  • Ten spools in one case for high-volume printing
  • Very low shrinkage keeps large flat prints dimensionally accurate
  • Stronger than ABS for durable functional parts
  • Glass-like clarity achievable with optical coatings

Tekniset tiedot

ColorRed
TypeFilament

Kysymyksiä tästä tuotteesta

How often will the 2.85mm nozzle need replacing with this filament?

The t-glase PET co-polymer is non-abrasive, so a standard brass nozzle lasts through many 1 lb spools; swap only when extrusion quality drops.

What limits a continuous multi-spool print run first?

Printing at 235-245 °C slows layer speed, so total print time per 1 lb spool becomes the practical limit before the next spool change.

How much heat and power does a 10-spool production run add?

Each spool prints at 235-245 °C with no heated bed required, keeping bed power at zero and hot-end load steady across all ten spools.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.