Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Five small stainless steel nozzles with M6 threads and 0.5mm openings

Unique-Bargains

Unique-Bargains 0.5mm MK8 Stainless Steel Nozzle 5pcs 1.75mm

SKU CH-7X7Q-GNW4Y

Five stainless-steel MK8 nozzles with a 0.5 mm bore for 1.75 mm filament, M6 thread and 13 mm overall length

  • Precise 0.5 mm orifice for detailed prints
  • Stainless steel resists wear from abrasive filaments
  • M6 thread fits MK8 extruder heads directly
  • Five nozzles included for quick replacement cycles
  • Stamped size markings simplify identification

0.5 mm MK8 Stainless Steel Nozzle Pack

This set contains five stainless steel nozzles with a 0.5 mm bore for MK8 extruders. Each nozzle accepts 1.75 mm filament and features an M6 thread with a 5 mm thread length. The stainless steel construction resists wear from abrasive filaments better than standard brass nozzles.

Makers printing abrasive or standard filaments

Users who want a harder-wearing tip for materials such as carbon-fibre or glow-in-the-dark blends will benefit from the stainless steel body. Printers that do not use an MK8 hot-end or that require a different bore size cannot use these nozzles.

Verify MK8 compatibility

Confirm that your hot-end uses an M6 thread and matches the 13 mm overall length before ordering. After installation you must recalibrate the nozzle-to-bed distance to restore first-layer quality. Heat the block to the appropriate temperature range for your filament before removing or fitting a nozzle.

Kohokohdat

  • Precise 0.5 mm orifice for detailed prints
  • Stainless steel resists wear from abrasive filaments
  • M6 thread fits MK8 extruder heads directly
  • Five nozzles included for quick replacement cycles
  • Stamped size markings simplify identification

Tekniset tiedot

BrandUnique Bargains

Kysymyksiä tästä tuotteesta

Does my printer need an MK8 extruder with an M6 thread to use these 0.5mm nozzles?

Yes, they are made for MK8 extruder heads that use an M6 thread with a 5mm thread length.

Can I keep printing 1.75mm PLA or ABS with these stainless steel nozzles?

Yes, the 0.5mm bore and 2mm input are sized for 1.75mm filament and work with non-abrasive materials such as PLA and ABS.

How do I know the new nozzle is installed correctly after the hot-end reaches 180-220°C for PLA?

After heating, hold the heat block with a spanner and tighten the nozzle with a socket driver; then recalibrate the nozzle-to-bed distance and verify a clean first layer.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.