저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Five small stainless steel nozzles with M6 threads and 0.5mm openings

Unique-Bargains

Unique-Bargains 0.5mm MK8 Stainless Steel Nozzle 5pcs 1.75mm

SKU CH-7X7Q-GNW4Y

Five stainless-steel MK8 nozzles with a 0.5 mm bore for 1.75 mm filament, M6 thread and 13 mm overall length

  • Precise 0.5 mm orifice for detailed prints
  • Stainless steel resists wear from abrasive filaments
  • M6 thread fits MK8 extruder heads directly
  • Five nozzles included for quick replacement cycles
  • Stamped size markings simplify identification

0.5 mm MK8 Stainless Steel Nozzle Pack

This set contains five stainless steel nozzles with a 0.5 mm bore for MK8 extruders. Each nozzle accepts 1.75 mm filament and features an M6 thread with a 5 mm thread length. The stainless steel construction resists wear from abrasive filaments better than standard brass nozzles.

Makers printing abrasive or standard filaments

Users who want a harder-wearing tip for materials such as carbon-fibre or glow-in-the-dark blends will benefit from the stainless steel body. Printers that do not use an MK8 hot-end or that require a different bore size cannot use these nozzles.

Verify MK8 compatibility

Confirm that your hot-end uses an M6 thread and matches the 13 mm overall length before ordering. After installation you must recalibrate the nozzle-to-bed distance to restore first-layer quality. Heat the block to the appropriate temperature range for your filament before removing or fitting a nozzle.

주요 특징

  • Precise 0.5 mm orifice for detailed prints
  • Stainless steel resists wear from abrasive filaments
  • M6 thread fits MK8 extruder heads directly
  • Five nozzles included for quick replacement cycles
  • Stamped size markings simplify identification

사양

BrandUnique Bargains

이 상품에 대한 질문

Does my printer need an MK8 extruder with an M6 thread to use these 0.5mm nozzles?

Yes, they are made for MK8 extruder heads that use an M6 thread with a 5mm thread length.

Can I keep printing 1.75mm PLA or ABS with these stainless steel nozzles?

Yes, the 0.5mm bore and 2mm input are sized for 1.75mm filament and work with non-abrasive materials such as PLA and ABS.

How do I know the new nozzle is installed correctly after the hot-end reaches 180-220°C for PLA?

After heating, hold the heat block with a spanner and tighten the nozzle with a socket driver; then recalibrate the nozzle-to-bed distance and verify a clean first layer.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.