NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.
A-Tech
An 8 GB DDR3L 1066 ECC registered DIMM with 4Rx8 organisation and 1.35 V operation
This 8 GB DDR3L 1066 ECC registered DIMM is built for server and workstation platforms that require error-correcting memory. The module runs at PC3L-8500 speed with a CAS latency of CL7 and operates at the low 1.35 V DDR3L voltage. It targets administrators upgrading or repairing compatible IBM-Lenovo systems.
The stick uses a standard 240-pin DIMM form factor and a 4Rx8 rank layout with major-brand chips. Registered buffering reduces electrical load on the memory controller, allowing larger memory populations in multi-socket boards. The pin-out matches the DDR3L keying so it only fits slots wired for 1.35 V operation.
At 1.35 V the module draws less power and generates less heat than standard 1.5 V DDR3, helping chassis airflow in dense rack enclosures. ECC circuitry adds minimal overhead while correcting single-bit errors in real time. The registered design keeps signal integrity stable under sustained workloads without increasing acoustic noise.
| Brand | A-Tech |
|---|---|
| Capacity | 8GB |
| Speed | DDR3L 1066 (PC3L 8500) |
| CAS Latency | CL7 |
| Voltage | 1.35V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 4Rx8 |
| Chipset | Major Brand Chipset |
| Features | Major Brand Chips |
It runs at DDR3L 1066 (PC3L-8500) with CL7 latency and 1.35V operation.
A DDR3 DIMM slot with 240 pins; the registered design requires a server or workstation motherboard that supports RDIMMs.
Power down, open the chassis, align the notch on the 240-pin edge connector, press firmly until both clips lock, then verify in BIOS that ECC and registered modes are enabled.
Također u ovoj kategoriji
Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.
Ono što šaljete, i ono u čemu gledate cijene.
Poslano iz Vašeg novčanika na blagajni
Samo prikaz — katalog je izražen u dolarima
Nijedna valuta ne odgovara.
Odaberite jezik na kojem Vam se stranica obraća.
Novi ste ovdje?
Već imate račun?
Ne postoji automatsko resetiranje: ova trgovina ne šalje e-poštu, stoga ne postoji jednokratna poveznica koju biste mogli zatražiti. Ostavite adresu uz svoj račun, netko će je ručno obraditi.
Zahtjev zaprimljen
Ništa neće stići u Vaš pretinac e-pošte — ova trgovina uopće ne šalje e-poštu. Netko će to ručno preuzeti.
Sjetili ste se?