Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.

Praćeni artikli Prijava
Green circuit board with RJ45 port and three USB sockets, pogo pins along one edge

LORDWORLD

LORDWORLD Ethernet USB HUB HAT B 1x RJ45 3x USB 2.0 development board

SKU CH-8QPG-R28YN

Adds one RJ45 Ethernet port and three USB 2.0 ports to Raspberry Pi Zero and larger models using pogo pins or a USB cable

  • Adds wired networking with 10/100M auto-negotiation via RTL8152B chip
  • Expands connectivity using three USB 2.0 ports compatible with 1.1 devices
  • Attaches directly to Pi Zero boards through pogo pin interface
  • Connects to Pi 4B, 3B+, 3A+ or 2B via USB HUB cable
  • Plug-and-play design requires no driver installation for immediate use

Product identity

The LORDWORLD Ethernet USB HUB HAT B adds one RJ45 port and three USB 2.0 ports to Raspberry Pi boards. It uses an RTL8152B chip for 10/100M auto-negotiation and connects either through pogo pins on Zero models or a USB cable on larger Pi boards.

Target users and limits

Makers who need wired networking and extra USB ports on a Pi Zero, 3A+, 3B+, 2B or 4B will find this convenient. Builders who require gigabit Ethernet, USB 3.0 speeds or Power-over-Ethernet should look elsewhere because the hardware does not support those standards.

Installation notes

The pogo pin header aligns directly with the Zero GPIO for a solderless fit, while other Pi models use the supplied USB link cable. No drivers are needed on standard Raspberry Pi OS. Misaligned pogo pins are the most common issue; press the HAT firmly and evenly to ensure all contacts engage.

Istaknuto

  • Adds wired networking with 10/100M auto-negotiation via RTL8152B chip
  • Expands connectivity using three USB 2.0 ports compatible with 1.1 devices
  • Attaches directly to Pi Zero boards through pogo pin interface
  • Connects to Pi 4B, 3B+, 3A+ or 2B via USB HUB cable
  • Plug-and-play design requires no driver installation for immediate use

Specifikacije

BrandLORDWORLD

Pitanja o ovom artiklu

Which Raspberry Pi models can I connect directly with the pogo pins?

The pogo pin design connects directly to Raspberry Pi Zero, Zero W, and Zero WH boards.

Can I use this HAT with a Raspberry Pi 4B without the pogo pins?

Yes, the USB HUB connector links to Raspberry Pi 4B, 3B+, 3A+, and 2B through a USB cable.

How do I verify the Ethernet link is running at 100 Mbit/s after setup?

Check the connection status on the Pi; the RTL8152B chip auto-negotiates 10/100M and will show 100 Mbps when the link is at full speed.

Također u ovoj kategoriji

Kupci su usporedili ovo

Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.