Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with RJ45 port and three USB sockets, pogo pins along one edge

LORDWORLD

LORDWORLD Ethernet USB HUB HAT B 1x RJ45 3x USB 2.0 development board

SKU CH-8QPG-R28YN

Adds one RJ45 Ethernet port and three USB 2.0 ports to Raspberry Pi Zero and larger models using pogo pins or a USB cable

  • Adds wired networking with 10/100M auto-negotiation via RTL8152B chip
  • Expands connectivity using three USB 2.0 ports compatible with 1.1 devices
  • Attaches directly to Pi Zero boards through pogo pin interface
  • Connects to Pi 4B, 3B+, 3A+ or 2B via USB HUB cable
  • Plug-and-play design requires no driver installation for immediate use

Product identity

The LORDWORLD Ethernet USB HUB HAT B adds one RJ45 port and three USB 2.0 ports to Raspberry Pi boards. It uses an RTL8152B chip for 10/100M auto-negotiation and connects either through pogo pins on Zero models or a USB cable on larger Pi boards.

Target users and limits

Makers who need wired networking and extra USB ports on a Pi Zero, 3A+, 3B+, 2B or 4B will find this convenient. Builders who require gigabit Ethernet, USB 3.0 speeds or Power-over-Ethernet should look elsewhere because the hardware does not support those standards.

Installation notes

The pogo pin header aligns directly with the Zero GPIO for a solderless fit, while other Pi models use the supplied USB link cable. No drivers are needed on standard Raspberry Pi OS. Misaligned pogo pins are the most common issue; press the HAT firmly and evenly to ensure all contacts engage.

Kohokohdat

  • Adds wired networking with 10/100M auto-negotiation via RTL8152B chip
  • Expands connectivity using three USB 2.0 ports compatible with 1.1 devices
  • Attaches directly to Pi Zero boards through pogo pin interface
  • Connects to Pi 4B, 3B+, 3A+ or 2B via USB HUB cable
  • Plug-and-play design requires no driver installation for immediate use

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

Which Raspberry Pi models can I connect directly with the pogo pins?

The pogo pin design connects directly to Raspberry Pi Zero, Zero W, and Zero WH boards.

Can I use this HAT with a Raspberry Pi 4B without the pogo pins?

Yes, the USB HUB connector links to Raspberry Pi 4B, 3B+, 3A+, and 2B through a USB cable.

How do I verify the Ethernet link is running at 100 Mbit/s after setup?

Check the connection status on the Pi; the RTL8152B chip auto-negotiates 10/100M and will show 100 Mbps when the link is at full speed.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.