Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Small black square brushless fan with thin wires and a tiny white connector

Adafruit

Adafruit 5V Mini Cooling Fan 30mm Molex PicoBlade 1.25mm

SKU CH-60CV-SWXQY

A 30mm brushless DC fan with a Molex PicoBlade connector draws .2 A at 5 V to cool small computers or FPGA boards

  • TypePrototyping Products
  • Brushless DC motor runs quietly at 5V
  • Compact 30mm square frame fits tight project enclosures
  • Molex PicoBlade 1.25mm pitch plug connects straight to compatible headers
  • Draws only .2 A leaving headroom on small power supplies
  • Includes four M2.5 screws 16mm long plus hex nuts for secure mounting

Compact 5 V brushless fan

This 30 mm by 30 mm by 8 mm brushless DC fan runs from a 5 V supply and draws 0.2 A. It is built for prototyping and small-form-factor cooling where space is at a premium. The included Molex PicoBlade 1.25 mm pitch connector plugs straight onto compatible headers, and the hard-ware kit supplies four M2.5 screws 16 mm long with hex nuts.

Makers who need plug-and-play airflow

Hobbyists and engineers adding active cooling to Raspberry Pi, FPGA or motor-driver boards will appreciate the ready-made cable and mounting hardware. Builders who require variable-speed control or a PWM signal should look elsewhere, as this unit operates at a fixed speed. Projects that demand higher static pressure or larger airflow volumes will also need a different solution.

Molex PicoBlade 1.25 mm connector

The 2-pin PicoBlade header is the single interface that determines whether the fan fits your board without soldering. If your controller or breakout carries the matching 1.25 mm pitch receptacle, the fan connects in seconds; otherwise you must cut the connector and solder or clamp the bare wires.

Helstu kostir

  • Brushless DC motor runs quietly at 5V
  • Compact 30mm square frame fits tight project enclosures
  • Molex PicoBlade 1.25mm pitch plug connects straight to compatible headers
  • Draws only .2 A leaving headroom on small power supplies
  • Includes four M2.5 screws 16mm long plus hex nuts for secure mounting

Tæknilýsing

TypePrototyping Products

Spurningar um þessa vöru

How much power does the 5V Mini Cooling Fan draw when running continuously?

The brushless DC fan operates at 5V and draws 0.2 A, so it uses about 1 watt while running all day.

What connector must my board provide for the Molex PicoBlade 1.25mm plug?

You need a matching 2-pin Molex PicoBlade header with 1.25mm pitch on your board, or you can cut the connector and solder the wires directly.

Will the included M2.5 hardware fit the mounting holes on my existing Raspberry Pi case?

The kit supplies four M2.5 Phillips screws 16mm long with hex nuts; they fit the fan's 30mm square frame but may not match other devices' hole patterns.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.