Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small black square brushless fan with thin wires and a tiny white connector

Adafruit

Adafruit 5V Mini Cooling Fan 30mm Molex PicoBlade 1.25mm

SKU CH-60CV-SWXQY

A 30mm brushless DC fan with a Molex PicoBlade connector draws .2 A at 5 V to cool small computers or FPGA boards

  • TypePrototyping Products
  • Brushless DC motor runs quietly at 5V
  • Compact 30mm square frame fits tight project enclosures
  • Molex PicoBlade 1.25mm pitch plug connects straight to compatible headers
  • Draws only .2 A leaving headroom on small power supplies
  • Includes four M2.5 screws 16mm long plus hex nuts for secure mounting

Compact 5 V brushless fan

This 30 mm by 30 mm by 8 mm brushless DC fan runs from a 5 V supply and draws 0.2 A. It is built for prototyping and small-form-factor cooling where space is at a premium. The included Molex PicoBlade 1.25 mm pitch connector plugs straight onto compatible headers, and the hard-ware kit supplies four M2.5 screws 16 mm long with hex nuts.

Makers who need plug-and-play airflow

Hobbyists and engineers adding active cooling to Raspberry Pi, FPGA or motor-driver boards will appreciate the ready-made cable and mounting hardware. Builders who require variable-speed control or a PWM signal should look elsewhere, as this unit operates at a fixed speed. Projects that demand higher static pressure or larger airflow volumes will also need a different solution.

Molex PicoBlade 1.25 mm connector

The 2-pin PicoBlade header is the single interface that determines whether the fan fits your board without soldering. If your controller or breakout carries the matching 1.25 mm pitch receptacle, the fan connects in seconds; otherwise you must cut the connector and solder or clamp the bare wires.

Kohokohdat

  • Brushless DC motor runs quietly at 5V
  • Compact 30mm square frame fits tight project enclosures
  • Molex PicoBlade 1.25mm pitch plug connects straight to compatible headers
  • Draws only .2 A leaving headroom on small power supplies
  • Includes four M2.5 screws 16mm long plus hex nuts for secure mounting

Tekniset tiedot

TypePrototyping Products

Kysymyksiä tästä tuotteesta

How much power does the 5V Mini Cooling Fan draw when running continuously?

The brushless DC fan operates at 5V and draws 0.2 A, so it uses about 1 watt while running all day.

What connector must my board provide for the Molex PicoBlade 1.25mm plug?

You need a matching 2-pin Molex PicoBlade header with 1.25mm pitch on your board, or you can cut the connector and solder the wires directly.

Will the included M2.5 hardware fit the mounting holes on my existing Raspberry Pi case?

The kit supplies four M2.5 Phillips screws 16mm long with hex nuts; they fit the fan's 30mm square frame but may not match other devices' hole patterns.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.