Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Small black square brushless fan with thin wires and a tiny white connector

Adafruit

Adafruit 5V Mini Cooling Fan 30mm Molex PicoBlade 1.25mm

SKU CH-60CV-SWXQY

A 30mm brushless DC fan with a Molex PicoBlade connector draws .2 A at 5 V to cool small computers or FPGA boards

  • TypePrototyping Products
  • Brushless DC motor runs quietly at 5V
  • Compact 30mm square frame fits tight project enclosures
  • Molex PicoBlade 1.25mm pitch plug connects straight to compatible headers
  • Draws only .2 A leaving headroom on small power supplies
  • Includes four M2.5 screws 16mm long plus hex nuts for secure mounting

Compact 5 V brushless fan

This 30 mm by 30 mm by 8 mm brushless DC fan runs from a 5 V supply and draws 0.2 A. It is built for prototyping and small-form-factor cooling where space is at a premium. The included Molex PicoBlade 1.25 mm pitch connector plugs straight onto compatible headers, and the hard-ware kit supplies four M2.5 screws 16 mm long with hex nuts.

Makers who need plug-and-play airflow

Hobbyists and engineers adding active cooling to Raspberry Pi, FPGA or motor-driver boards will appreciate the ready-made cable and mounting hardware. Builders who require variable-speed control or a PWM signal should look elsewhere, as this unit operates at a fixed speed. Projects that demand higher static pressure or larger airflow volumes will also need a different solution.

Molex PicoBlade 1.25 mm connector

The 2-pin PicoBlade header is the single interface that determines whether the fan fits your board without soldering. If your controller or breakout carries the matching 1.25 mm pitch receptacle, the fan connects in seconds; otherwise you must cut the connector and solder or clamp the bare wires.

Přednosti

  • Brushless DC motor runs quietly at 5V
  • Compact 30mm square frame fits tight project enclosures
  • Molex PicoBlade 1.25mm pitch plug connects straight to compatible headers
  • Draws only .2 A leaving headroom on small power supplies
  • Includes four M2.5 screws 16mm long plus hex nuts for secure mounting

Specifikace

TypePrototyping Products

Otázky k tomuto produktu

How much power does the 5V Mini Cooling Fan draw when running continuously?

The brushless DC fan operates at 5V and draws 0.2 A, so it uses about 1 watt while running all day.

What connector must my board provide for the Molex PicoBlade 1.25mm plug?

You need a matching 2-pin Molex PicoBlade header with 1.25mm pitch on your board, or you can cut the connector and solder the wires directly.

Will the included M2.5 hardware fit the mounting holes on my existing Raspberry Pi case?

The kit supplies four M2.5 Phillips screws 16mm long with hex nuts; they fit the fan's 30mm square frame but may not match other devices' hole patterns.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.