Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Black base clear lid polycarbonate case for Pi Zero 20

Adafruit

Adafruit Raspberry Pi Zero Case Black Clear 20

SKU CH-PDXW-FGVPE

Protects Raspberry Pi Zero models with a durable polycarbonate shell that keeps all ports accessible

  • TypePrototyping Products
  • Protects your Pi Zero with a secure snap-fit enclosure
  • Ultra-durable, super-glossy polycarbonate construction resists everyday knocks
  • Compatible with Pi Zero, Pi Zero W and Pi Zero 2 W
  • All edge connectors remain accessible including mini HDMI, microSD and microUSB ports
  • Clear top and black base two-piece design lets you see the board inside

Raspberry Pi Zero Enclosure

This black-base, clear-top polycarbonate case is built for the Raspberry Pi Zero, Zero W and Zero 2 W. It snaps together in two pieces and latches the board on corner pegs for a secure fit. All edge connectors — mini HDMI, microSD slot, microUSB power and microUSB data — remain accessible through slim openings. A cutout also allows a 2×20-pin header to be soldered in place.

Thermals Noise And Power

The enclosure is a passive shell with no fan, no active cooling and no power draw of its own. Polycarbonate walls transmit the board's heat to the surrounding air without adding audible noise. Because the case adds no electronics, it does not change the Pi's power consumption or thermal profile in any measurable way.

Upgrade Path And Fit

The case replaces a bare board or a loose 3D-printed shell when a tidy, pocket-sized enclosure is required. It is worth fitting when the project moves from bench to bag, toolbox or permanent install and needs protected ports and a latched lid. Builders needing HAT clearance, internal battery space or mounting holes will need a different enclosure.

Helstu kostir

  • Protects your Pi Zero with a secure snap-fit enclosure
  • Ultra-durable, super-glossy polycarbonate construction resists everyday knocks
  • Compatible with Pi Zero, Pi Zero W and Pi Zero 2 W
  • All edge connectors remain accessible including mini HDMI, microSD and microUSB ports
  • Clear top and black base two-piece design lets you see the board inside

Tæknilýsing

TypePrototyping Products

Spurningar um þessa vöru

How do I snap the Pi Zero into the case without cracking the corner pegs?

Seat the board flat in the black base so each corner clicks into its peg, then press the clear lid straight down until it locks; forcing the lid at an angle stresses the pegs and can snap them off.

Will the polycarbonate lid yellow or need replacement after long indoor use?

The super-glossy polycarbonate resists yellowing under normal indoor light, so no scheduled replacement is needed unless the lid is cracked from impact.

At what point does the sealed case start throttling the Pi Zero 2 W during sustained loads?

With no ventilation slots the enclosure traps heat; the Pi Zero 2 W typically hits its thermal throttle point within a few minutes of continuous full-load operation.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.