저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Black base clear lid polycarbonate case for Pi Zero 20

Adafruit

Adafruit Raspberry Pi Zero Case Black Clear 20

SKU CH-PDXW-FGVPE

Protects Raspberry Pi Zero models with a durable polycarbonate shell that keeps all ports accessible

  • TypePrototyping Products
  • Protects your Pi Zero with a secure snap-fit enclosure
  • Ultra-durable, super-glossy polycarbonate construction resists everyday knocks
  • Compatible with Pi Zero, Pi Zero W and Pi Zero 2 W
  • All edge connectors remain accessible including mini HDMI, microSD and microUSB ports
  • Clear top and black base two-piece design lets you see the board inside

Raspberry Pi Zero Enclosure

This black-base, clear-top polycarbonate case is built for the Raspberry Pi Zero, Zero W and Zero 2 W. It snaps together in two pieces and latches the board on corner pegs for a secure fit. All edge connectors — mini HDMI, microSD slot, microUSB power and microUSB data — remain accessible through slim openings. A cutout also allows a 2×20-pin header to be soldered in place.

Thermals Noise And Power

The enclosure is a passive shell with no fan, no active cooling and no power draw of its own. Polycarbonate walls transmit the board's heat to the surrounding air without adding audible noise. Because the case adds no electronics, it does not change the Pi's power consumption or thermal profile in any measurable way.

Upgrade Path And Fit

The case replaces a bare board or a loose 3D-printed shell when a tidy, pocket-sized enclosure is required. It is worth fitting when the project moves from bench to bag, toolbox or permanent install and needs protected ports and a latched lid. Builders needing HAT clearance, internal battery space or mounting holes will need a different enclosure.

주요 특징

  • Protects your Pi Zero with a secure snap-fit enclosure
  • Ultra-durable, super-glossy polycarbonate construction resists everyday knocks
  • Compatible with Pi Zero, Pi Zero W and Pi Zero 2 W
  • All edge connectors remain accessible including mini HDMI, microSD and microUSB ports
  • Clear top and black base two-piece design lets you see the board inside

사양

TypePrototyping Products

이 상품에 대한 질문

How do I snap the Pi Zero into the case without cracking the corner pegs?

Seat the board flat in the black base so each corner clicks into its peg, then press the clear lid straight down until it locks; forcing the lid at an angle stresses the pegs and can snap them off.

Will the polycarbonate lid yellow or need replacement after long indoor use?

The super-glossy polycarbonate resists yellowing under normal indoor light, so no scheduled replacement is needed unless the lid is cracked from impact.

At what point does the sealed case start throttling the Pi Zero 2 W during sustained loads?

With no ventilation slots the enclosure traps heat; the Pi Zero 2 W typically hits its thermal throttle point within a few minutes of continuous full-load operation.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.