暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Black base clear lid polycarbonate case for Pi Zero 20

Adafruit

Adafruit Raspberry Pi Zero Case Black Clear 20

SKU CH-PDXW-FGVPE

Protects Raspberry Pi Zero models with a durable polycarbonate shell that keeps all ports accessible

  • TypePrototyping Products
  • Protects your Pi Zero with a secure snap-fit enclosure
  • Ultra-durable, super-glossy polycarbonate construction resists everyday knocks
  • Compatible with Pi Zero, Pi Zero W and Pi Zero 2 W
  • All edge connectors remain accessible including mini HDMI, microSD and microUSB ports
  • Clear top and black base two-piece design lets you see the board inside

Raspberry Pi Zero Enclosure

This black-base, clear-top polycarbonate case is built for the Raspberry Pi Zero, Zero W and Zero 2 W. It snaps together in two pieces and latches the board on corner pegs for a secure fit. All edge connectors — mini HDMI, microSD slot, microUSB power and microUSB data — remain accessible through slim openings. A cutout also allows a 2×20-pin header to be soldered in place.

Thermals Noise And Power

The enclosure is a passive shell with no fan, no active cooling and no power draw of its own. Polycarbonate walls transmit the board's heat to the surrounding air without adding audible noise. Because the case adds no electronics, it does not change the Pi's power consumption or thermal profile in any measurable way.

Upgrade Path And Fit

The case replaces a bare board or a loose 3D-printed shell when a tidy, pocket-sized enclosure is required. It is worth fitting when the project moves from bench to bag, toolbox or permanent install and needs protected ports and a latched lid. Builders needing HAT clearance, internal battery space or mounting holes will need a different enclosure.

特長

  • Protects your Pi Zero with a secure snap-fit enclosure
  • Ultra-durable, super-glossy polycarbonate construction resists everyday knocks
  • Compatible with Pi Zero, Pi Zero W and Pi Zero 2 W
  • All edge connectors remain accessible including mini HDMI, microSD and microUSB ports
  • Clear top and black base two-piece design lets you see the board inside

仕様

TypePrototyping Products

この商品に関する質問

How do I snap the Pi Zero into the case without cracking the corner pegs?

Seat the board flat in the black base so each corner clicks into its peg, then press the clear lid straight down until it locks; forcing the lid at an angle stresses the pegs and can snap them off.

Will the polycarbonate lid yellow or need replacement after long indoor use?

The super-glossy polycarbonate resists yellowing under normal indoor light, so no scheduled replacement is needed unless the lid is cracked from impact.

At what point does the sealed case start throttling the Pi Zero 2 W during sustained loads?

With no ventilation slots the enclosure traps heat; the Pi Zero 2 W typically hits its thermal throttle point within a few minutes of continuous full-load operation.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。