Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Spool of grey 3D printer filament on a reel

E3D Online

E3D Online spoolWorks EDGE Filament 2.85mm 750g Cement Grey28 3D Printers Accessories

SKU CH-28A1-GPEN7

PETG-based filament combining ABS toughness with PLA ease for strong, low-warp prints

  • ColorGray
  • TypeFilament
  • Recyclable PETG-based material reduces environmental impact
  • Prints without unpleasant fumes or odours for comfortable use
  • Strong, tough filament with naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Works with Scaffold support for clean breakaway and reliable adhesion

Filament diameter and weight

This E3D spoolWorks EDGE filament comes in a 2.85 mm diameter on a 750 g spool. It is a PETG-based material developed in-house for 3D printing. The Cement Grey28 colour provides a naturally glossy finish. The spool is supplied new and ready to use.

Makers wanting tough PETG with low warp

The filament suits users who need strong, resilient parts with minimal warping and excellent layer adhesion. It prints easily without unpleasant fumes and sticks to the bed with a little gluestick. Builders who require a different diameter or a non-PETG material should look at other options.

2.85 mm diameter

The critical specification is the 2.85 mm filament diameter, which must match the printer’s extruder and hot-end system. Using the wrong diameter will cause feeding failures and print defects. Verify this figure against your hardware before purchase.

Priekšrocības

  • Recyclable PETG-based material reduces environmental impact
  • Prints without unpleasant fumes or odours for comfortable use
  • Strong, tough filament with naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Works with Scaffold support for clean breakaway and reliable adhesion

Specifikācijas

BrandE3D
ModelEdge
ColorGray
TypeFilament

Jautājumi par šo preci

How often will the 750 g spool need replacing during regular printing?

Replacement depends on print volume and part size; a 750 g spool yields many small models or fewer large ones before a new spool is required.

What limitation appears first during long, continuous prints with this Edge filament?

The spool will run out after the 750 g of material is consumed, which is the primary limit during extended sessions.

Does the filament produce noticeable fumes or heat when the printer runs all day?

The material prints with no unpleasant fumes or odors, and normal hot-end heat is the only thermal output during operation.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.