저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Spool of grey 3D printer filament on a reel

E3D Online

E3D Online spoolWorks EDGE Filament 2.85mm 750g Cement Grey28 3D Printers Accessories

SKU CH-28A1-GPEN7

PETG-based filament combining ABS toughness with PLA ease for strong, low-warp prints

  • ColorGray
  • TypeFilament
  • Recyclable PETG-based material reduces environmental impact
  • Prints without unpleasant fumes or odours for comfortable use
  • Strong, tough filament with naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Works with Scaffold support for clean breakaway and reliable adhesion

Filament diameter and weight

This E3D spoolWorks EDGE filament comes in a 2.85 mm diameter on a 750 g spool. It is a PETG-based material developed in-house for 3D printing. The Cement Grey28 colour provides a naturally glossy finish. The spool is supplied new and ready to use.

Makers wanting tough PETG with low warp

The filament suits users who need strong, resilient parts with minimal warping and excellent layer adhesion. It prints easily without unpleasant fumes and sticks to the bed with a little gluestick. Builders who require a different diameter or a non-PETG material should look at other options.

2.85 mm diameter

The critical specification is the 2.85 mm filament diameter, which must match the printer’s extruder and hot-end system. Using the wrong diameter will cause feeding failures and print defects. Verify this figure against your hardware before purchase.

주요 특징

  • Recyclable PETG-based material reduces environmental impact
  • Prints without unpleasant fumes or odours for comfortable use
  • Strong, tough filament with naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Works with Scaffold support for clean breakaway and reliable adhesion

사양

BrandE3D
ModelEdge
ColorGray
TypeFilament

이 상품에 대한 질문

How often will the 750 g spool need replacing during regular printing?

Replacement depends on print volume and part size; a 750 g spool yields many small models or fewer large ones before a new spool is required.

What limitation appears first during long, continuous prints with this Edge filament?

The spool will run out after the 750 g of material is consumed, which is the primary limit during extended sessions.

Does the filament produce noticeable fumes or heat when the printer runs all day?

The material prints with no unpleasant fumes or odors, and normal hot-end heat is the only thermal output during operation.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.