نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.

قائمة الرصد تسجيل الدخول
Spool of grey 3D printer filament on a reel

E3D Online

E3D Online spoolWorks EDGE Filament 2.85mm 750g Cement Grey28 3D Printers Accessories

SKU CH-28A1-GPEN7

PETG-based filament combining ABS toughness with PLA ease for strong, low-warp prints

  • ColorGray
  • TypeFilament
  • Recyclable PETG-based material reduces environmental impact
  • Prints without unpleasant fumes or odours for comfortable use
  • Strong, tough filament with naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Works with Scaffold support for clean breakaway and reliable adhesion

Filament diameter and weight

This E3D spoolWorks EDGE filament comes in a 2.85 mm diameter on a 750 g spool. It is a PETG-based material developed in-house for 3D printing. The Cement Grey28 colour provides a naturally glossy finish. The spool is supplied new and ready to use.

Makers wanting tough PETG with low warp

The filament suits users who need strong, resilient parts with minimal warping and excellent layer adhesion. It prints easily without unpleasant fumes and sticks to the bed with a little gluestick. Builders who require a different diameter or a non-PETG material should look at other options.

2.85 mm diameter

The critical specification is the 2.85 mm filament diameter, which must match the printer’s extruder and hot-end system. Using the wrong diameter will cause feeding failures and print defects. Verify this figure against your hardware before purchase.

أبرز المميزات

  • Recyclable PETG-based material reduces environmental impact
  • Prints without unpleasant fumes or odours for comfortable use
  • Strong, tough filament with naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Works with Scaffold support for clean breakaway and reliable adhesion

المواصفات

BrandE3D
ModelEdge
ColorGray
TypeFilament

أسئلة حول هذا المنتج

How often will the 750 g spool need replacing during regular printing?

Replacement depends on print volume and part size; a 750 g spool yields many small models or fewer large ones before a new spool is required.

What limitation appears first during long, continuous prints with this Edge filament?

The spool will run out after the 750 g of material is consumed, which is the primary limit during extended sessions.

Does the filament produce noticeable fumes or heat when the printer runs all day?

The material prints with no unpleasant fumes or odors, and normal hot-end heat is the only thermal output during operation.

أيضًا في هذا القسم

عملاء قارنوا هذه المنتجات

نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.