BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.
NEMIX RAM
An 8 GB DDR3 SODIMM running at 1066 MHz with CL7 latency and 1.5 V for laptop upgrades
This 8GB module uses 204-pin DDR3 technology running at 1066MHz with a CL7 latency. It targets laptops, all-in-one PCs, small-form-factor systems and NAS devices that accept PC3-8500 unbuffered non-ECC memory. The single-stick design leaves other slots free for future expansion.
Operating at 1.50V, the module draws typical DDR3 power without a heat spreader, relying on the system's existing airflow. Unbuffered non-ECC construction keeps electrical load low for the memory controller. Acoustic profile is silent because there are no moving parts on the stick itself.
The 8GB density is delivered through a 2Rx8 organisation, which determines compatibility with the memory controller's rank limits. Systems that only support single-rank modules or that cap total memory below 8GB per slot cannot use this stick. Verify the platform's maximum rank and per-slot capacity before purchase.
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM DDR3 Orignial Series 204-Pin NON-ECC Unbuffered SODIMM Memory |
| Model | DDR3 NON- ECC Unbuffered SODIMM Laptop, AIO, SFF, NAS Storage Device Memory |
| Part Number | MS8500-828K1 |
| Capacity | 8GB |
| Type | 204-Pin DDR3 SO-DIMM |
| Speed | DDR3 1066 (PC3 8500) |
| CAS Latency | CL7 |
| Voltage | 1.50V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Heat Spreader | No |
| Features | DDR3 Laptop, AIO All-in-One, SFF, NAS Device Compatible |
Power off the laptop, remove the battery if possible, open the memory compartment, align the notch on the module with the slot key, insert at an angle then press down until the clips click. The step people miss is fully seating both clips before closing the case.
No scheduled maintenance is required; the module has no heat spreader and runs at 1.5V. If a memory error appears, run a diagnostic and replace the stick if it fails — there are no user-serviceable parts.
The 1066MHz speed and CL7 latency set the throughput ceiling; under continuous heavy load the memory bus saturates before voltage or thermal limits become an issue.
Også i denne avdelingen
Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.
Det du betaler med, og det du ser prisene i.
Sendes fra lommeboken din i kassen
Kun visning — katalogen er prissatt i USD
Fant ingen valuta.
Velg språket nettstedet snakker til deg på.
Ingen språk samsvarer.
Ny her?
Har du allerede en konto?
Det finnes ingen automatisk tilbakestilling: butikken sender ikke e-post, så det finnes ingen engangslenke å be om. La adressen stå på kontoen, så blir den behandlet manuelt.
Forespørsel registrert
Ingenting er på vei til innboksen din — butikken sender ingen e-post i det hele tatt. Noen behandler dette manuelt.
Husket du det likevel?