Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Rectangular aluminium power supply, silver finish, screw terminals visible

myVolts

myVolts S-100-24 24V 4.2A 100W AT Power Supply

SKU CH-178X-099WQ

24V 4.2A 100W AT switch-mode supply with overload, over-voltage and short-circuit protection, CCC/FCC/CE compliant for industrial, LED and 3D-printer use

  • TypeAT
  • Reliable operation from 0 to 40 °C ambient
  • High efficiency with low DC ripple for stable output
  • circuit, overload and over-voltage protection built in
  • 100 % full-load burn-in test ensures dependable start-up
  • Strong insulation and CCC, FCC, CE safety compliance

Industrial 24V AT Supply

This myVolts S-100-24 unit delivers 24 volts at 4.2 amps for 100 watts of continuous power. It accepts a universal AC input from 100 to 240 volts and provides DC output through L, N, GND and V terminals with an adjustable voltage tap. The aluminium alloy enclosure relies on natural convection cooling. It suits industrial automation, LED displays, CCTV, radio equipment, 3D printers and similar 24 V DC loads.

Wiring and Mounting

Installation requires connecting live and neutral to the AC input terminals and securing the DC load to the GND and V outputs; the ADJ terminal allows fine voltage trimming. No forced-air cooling is present, so the unit must be mounted with free airflow around its aluminium case. The screw-terminal block demands correct polarity — reversed DC connections will trigger the protection circuit. Operating temperature range is 0 to 40 °C with up to 95 % non-condensing humidity.

Pre-Purchase Checks

Verify that your equipment requires a 24 V DC supply rated at or below 4.2 A and can tolerate the AT form factor. Confirm the available mounting space accommodates the approximate 85 x 58 x 33 mm footprint and that natural convection is sufficient for the installation environment. Ensure the AC mains voltage at the site falls within the 100 to 240 V range and that local regulations accept CCC, FCC and CE compliance marks.

Puncte forte

  • Reliable operation from 0 to 40 °C ambient
  • High efficiency with low DC ripple for stable output
  • circuit, overload and over-voltage protection built in
  • 100 % full-load burn-in test ensures dependable start-up
  • Strong insulation and CCC, FCC, CE safety compliance

Specificații

TypeAT

Întrebări despre acest articol

How can I confirm the S-100-24 is delivering a stable 24 V after installation?

Measure the DC output with a multimeter; it should read close to 24 V with minimal ripple, and the unit should run without triggering its short-circuit, overload or over-voltage protections.

What comes in the box with the S-100-24 and what must I source separately?

The supply itself is included; you must provide an AC mains cable for the L and N terminals and your own DC wiring for the V+ and GND outputs.

Which model from the comparison table should I choose if I need 4.2 A at 24 V?

Select the S-100-24, rated at 100 W and 4.2 A; the S-48-24 and S-60-24 only supply 2 A each.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.