Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Rectangular aluminium power supply, silver finish, screw terminals visible

myVolts

myVolts S-100-24 24V 4.2A 100W AT Power Supply

SKU CH-178X-099WQ

24V 4.2A 100W AT switch-mode supply with overload, over-voltage and short-circuit protection, CCC/FCC/CE compliant for industrial, LED and 3D-printer use

  • TypeAT
  • Reliable operation from 0 to 40 °C ambient
  • High efficiency with low DC ripple for stable output
  • circuit, overload and over-voltage protection built in
  • 100 % full-load burn-in test ensures dependable start-up
  • Strong insulation and CCC, FCC, CE safety compliance

Industrial 24V AT Supply

This myVolts S-100-24 unit delivers 24 volts at 4.2 amps for 100 watts of continuous power. It accepts a universal AC input from 100 to 240 volts and provides DC output through L, N, GND and V terminals with an adjustable voltage tap. The aluminium alloy enclosure relies on natural convection cooling. It suits industrial automation, LED displays, CCTV, radio equipment, 3D printers and similar 24 V DC loads.

Wiring and Mounting

Installation requires connecting live and neutral to the AC input terminals and securing the DC load to the GND and V outputs; the ADJ terminal allows fine voltage trimming. No forced-air cooling is present, so the unit must be mounted with free airflow around its aluminium case. The screw-terminal block demands correct polarity — reversed DC connections will trigger the protection circuit. Operating temperature range is 0 to 40 °C with up to 95 % non-condensing humidity.

Pre-Purchase Checks

Verify that your equipment requires a 24 V DC supply rated at or below 4.2 A and can tolerate the AT form factor. Confirm the available mounting space accommodates the approximate 85 x 58 x 33 mm footprint and that natural convection is sufficient for the installation environment. Ensure the AC mains voltage at the site falls within the 100 to 240 V range and that local regulations accept CCC, FCC and CE compliance marks.

Přednosti

  • Reliable operation from 0 to 40 °C ambient
  • High efficiency with low DC ripple for stable output
  • circuit, overload and over-voltage protection built in
  • 100 % full-load burn-in test ensures dependable start-up
  • Strong insulation and CCC, FCC, CE safety compliance

Specifikace

TypeAT

Otázky k tomuto produktu

How can I confirm the S-100-24 is delivering a stable 24 V after installation?

Measure the DC output with a multimeter; it should read close to 24 V with minimal ripple, and the unit should run without triggering its short-circuit, overload or over-voltage protections.

What comes in the box with the S-100-24 and what must I source separately?

The supply itself is included; you must provide an AC mains cable for the L and N terminals and your own DC wiring for the V+ and GND outputs.

Which model from the comparison table should I choose if I need 4.2 A at 24 V?

Select the S-100-24, rated at 100 W and 4.2 A; the S-48-24 and S-60-24 only supply 2 A each.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.