BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 USD
0.00277883BTC
În stoc
NEMIX RAM
NEMIX RAM 8GB DDR4 2400 CL17 260-PIN SODIMM for POSIFLEX HS-6510 memory upgrade
8GB DDR4 2400 CL17 260-pin SODIMM upgrades POSIFLEX HS-6510 terminals with 1.2V unbuffered memory
- Capacity8GB
- SpeedDDR4 2400 (PC4 19200)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.20V
- 8GB capacity expands POS terminal multitasking headroom
- DDR4 2400 speed matches HS-6510 memory bus
- CL17 latency keeps transaction processing responsive
- 2V operation reduces power draw in compact chassis
- 260-pin SODIMM form factor fits all-in-one slot directly
POSIFLEX HS-6510 memory upgrade
This 8 GB DDR4 SODIMM is built specifically for the POSIFLEX HS-6510 all-in-one terminal. It delivers a direct drop-in upgrade for point-of-sale and kiosk systems that require 260-pin unbuffered memory.
Thermals and power draw
Operating at 1.20 V with CL17 latency, the module runs without a heat spreader and draws minimal power in typical terminal workloads. The low-voltage DDR4 design keeps thermals manageable inside compact enclosures.
Packaged for immediate installation
The single 8 GB stick arrives ready to install with no additional cables, brackets or software required. Compatibility is validated for the target system so the upgrade proceeds without configuration changes.
Puncte forte
- 8GB capacity expands POS terminal multitasking headroom
- DDR4 2400 speed matches HS-6510 memory bus
- CL17 latency keeps transaction processing responsive
- 2V operation reduces power draw in compact chassis
- 260-pin SODIMM form factor fits all-in-one slot directly
Specificații
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR4 2400MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS19200-828K1 |
| Capacity | 8GB |
| Speed | DDR4 2400 (PC4 19200) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.20V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL17 |
| Heat Spreader | No |
| Type | 260-PIN DDR4 SODIMM |
| Rank | 2Rx8 |
| Features | DDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 8GB (1X8GB) DDR4 2400MHZ PC4-19200 2Rx8 1.2V CL17 260-PIN Non-ECC Unbuffered SODIMM |
Întrebări despre acest articol
How is the 260-pin SODIMM installed in the POSIFLEX HS-6510, and what step is often missed?
Power off the terminal and disconnect the power cord. Remove the memory cover on the base. Align the notch on the 260-pin module with the slot key, insert at an angle, then press down firmly until both side clips click. The step often missed is verifying both clips lock.
What maintenance or replacement will this DDR4 2400 module need later?
No scheduled maintenance is required. The module has no heat spreader and runs at 1.20V. If errors appear, run a memory diagnostic. Replacement is only needed if a fault develops; the CL17 2Rx8 stick is a single 8GB unit, so swap the whole module.
What limit appears first under sustained heavy workloads on this POSIFLEX memory?
The CL17 latency at DDR4 2400 (PC4-19200) sets the throughput ceiling. With 2Rx8 organisation and no heat spreader, sustained writes can hit thermal throttling before bandwidth saturates, causing the memory controller to insert wait states.
Tot din acest raion
Clienții au comparat și acestea.
Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.
