We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
A green circuit board with gold contacts and black memory chips, no heat spreader

NEMIX RAM

NEMIX RAM 8GB DDR4 2400 CL17 260-PIN SODIMM for POSIFLEX HS-6510 memory upgrade

SKU CH-4XE2-2EZYH

8GB DDR4 2400 CL17 260-pin SODIMM upgrades POSIFLEX HS-6510 terminals with 1.2V unbuffered memory

  • Capacity8GB
  • SpeedDDR4 2400 (PC4 19200)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 8GB capacity expands POS terminal multitasking headroom
  • DDR4 2400 speed matches HS-6510 memory bus
  • CL17 latency keeps transaction processing responsive
  • 2V operation reduces power draw in compact chassis
  • 260-pin SODIMM form factor fits all-in-one slot directly

POSIFLEX HS-6510 memory upgrade

This 8 GB DDR4 SODIMM is built specifically for the POSIFLEX HS-6510 all-in-one terminal. It delivers a direct drop-in upgrade for point-of-sale and kiosk systems that require 260-pin unbuffered memory.

Thermals and power draw

Operating at 1.20 V with CL17 latency, the module runs without a heat spreader and draws minimal power in typical terminal workloads. The low-voltage DDR4 design keeps thermals manageable inside compact enclosures.

Packaged for immediate installation

The single 8 GB stick arrives ready to install with no additional cables, brackets or software required. Compatibility is validated for the target system so the upgrade proceeds without configuration changes.

Highlights

  • 8GB capacity expands POS terminal multitasking headroom
  • DDR4 2400 speed matches HS-6510 memory bus
  • CL17 latency keeps transaction processing responsive
  • 2V operation reduces power draw in compact chassis
  • 260-pin SODIMM form factor fits all-in-one slot directly

Specifications

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR4 2400MHZ Non-ECC Unbuffered SODIMM
Part NumberMS19200-828K1
Capacity8GB
SpeedDDR4 2400 (PC4 19200)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemPOSIFLEX POS
CAS LatencyCL17
Heat SpreaderNo
Type260-PIN DDR4 SODIMM
Rank2Rx8
FeaturesDDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content8GB (1X8GB) DDR4 2400MHZ PC4-19200 2Rx8 1.2V CL17 260-PIN Non-ECC Unbuffered SODIMM

Questions about this item

How is the 260-pin SODIMM installed in the POSIFLEX HS-6510, and what step is often missed?

Power off the terminal and disconnect the power cord. Remove the memory cover on the base. Align the notch on the 260-pin module with the slot key, insert at an angle, then press down firmly until both side clips click. The step often missed is verifying both clips lock.

What maintenance or replacement will this DDR4 2400 module need later?

No scheduled maintenance is required. The module has no heat spreader and runs at 1.20V. If errors appear, run a memory diagnostic. Replacement is only needed if a fault develops; the CL17 2Rx8 stick is a single 8GB unit, so swap the whole module.

What limit appears first under sustained heavy workloads on this POSIFLEX memory?

The CL17 latency at DDR4 2400 (PC4-19200) sets the throughput ceiling. With 2Rx8 organisation and no heat spreader, sustained writes can hit thermal throttling before bandwidth saturates, causing the memory controller to insert wait states.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.