Thermaltake
Thermaltake TOUGHFAN 14 Pro 140mm PWM 500-2000 RPM 119.6 CFM 2 Pack CL-F160-PL14BL-A
Two 140 mm PWM fans deliver up to 119.6 CFM at 2,000 RPM with Gen.2 hydraulic bearings for quiet operation down to 24.5 dB-A
- Fan Counts2 Fans
- TypeCase Fan
- Fan Size140mm
- Fan Thickness25mm
- Bearing TypeHydraulic Bearing Gen.2
- RPMPWM 500~2000 R.P.M With L.N.C PWM 500~1500 R.P.M
- 140 mm fans deliver 119.6 CFM airflow for strong cooling
- PWM control spans 500 to 2000 RPM for flexible speed management
- Gen.2 hydraulic bearing runs at 31.6 dB-A for quiet operation
- Low-noise adapter drops noise to 24.5 dB-A at 87.6 CFM
- Two-fan pack fits 140 mm mounts with 25 mm thickness
140mm PWM fan twin-pack
The Thermaltake TOUGHFAN 14 Pro arrives as a two-fan kit of 140mm case fans using 4-pin PWM control. Each unit runs from 500 to 2000 RPM and delivers 119.6 CFM airflow at 31.6 dB-A. A low-noise cable drops the range to 500-1500 RPM, 87.6 CFM and 24.5 dB-A. The Gen.2 hydraulic bearing and Liquid Crystal Polymer blades target builders who need high static pressure for radiators or dense chassis. Non-LED black finish suits stealth builds.
Radiator and restrictive-mesh upgrade
These fans replace lower-static-pressure 140mm models when airflow must push through thick radiators, dense filters or tight heatsink fins. The 3.57-H2O static pressure rating makes the jump worthwhile when existing fans stall in restrictive paths. The PWM curve and optional L.N.C. cable let you trade peak flow for quieter operation without changing hardware. Buyers who only need case airflow with minimal restriction may not see a proportional benefit.
140mm mount and 4-pin header check
Verify your case or radiator accepts 140mm fans at 25mm thickness and that the motherboard or controller provides a 4-pin PWM header for each fan. The low-noise cable requires a second header or a splitter if you want simultaneous speed reporting. No other mounting adapters or voltage converters are included. Ensure clearance for the fan frame and cable routing before ordering.
Puncte forte
- 140 mm fans deliver 119.6 CFM airflow for strong cooling
- PWM control spans 500 to 2000 RPM for flexible speed management
- Gen.2 hydraulic bearing runs at 31.6 dB-A for quiet operation
- Low-noise adapter drops noise to 24.5 dB-A at 87.6 CFM
- Two-fan pack fits 140 mm mounts with 25 mm thickness
Specificații
| Brand | Thermaltake |
|---|---|
| Series | TOUGHFAN Pro |
| Model | ToughFan Pro 14 (2 pack) |
| Part Number | CL-F160-PL14BL-A |
| Fan Counts | 2 Fans |
| Type | Case Fan |
| Fan Size | 140mm |
| Fan Thickness | 25mm |
| Bearing Type | Hydraulic Bearing Gen.2 |
| RPM | PWM 500~2000 R.P.M With L.N.C PWM 500~1500 R.P.M |
| Air Flow | 119.6 CFM With L.N.C 87.6 CFM |
| Noise Level | 31.6 dB-A With L.N.C 24.5 dB-A |
| Power Connector | 4 PIN PWM |
| Color | Black |
| LED | Non-LED |
| Greutate la expediere | 0.70 kg |
| Dimensiunile coletului | 210 × 158 × 60 mm |
Întrebări despre acest articol
Will the 140mm by 25mm frame fit my case or radiator mounts?
The fans are 140mm square and 25mm thick, matching the standard 140mm mounting pattern used on most cases and radiators.
How do I connect the 4-pin PWM cable and enable the L.N.C. low-noise mode?
Plug the 4-pin PWM connector into a motherboard PWM header; then enable L.N.C. mode in BIOS or fan-control software to limit speed to 1500 RPM.
When should I expect to replace the Gen.2 hydraulic bearings?
Hydraulic bearings are sealed and rated for long life; replace the fans if noise rises above 31.6 dB-A or airflow drops below 119.6 CFM at full speed.
Tot din acest raion
Clienții au comparat și acestea.
Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.
Black Box Corporation
Black Box Corporation DisplayPort to DVI Fibre Optic Cable 15 ft 4.5 m 1.35 GB/s
- Consumer Electronics
39,99 USD
0.0005154BTC
În stoc