Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
A black 1.75mm filament spool weighing 750g

E3D Online

E3D Online spoolWorks EDGE Filament 1.75mm 750g Very Black30 3D printers accessory

SKU CH-YX7Q-73BSE

PETG-based filament combining ABS toughness with PLA ease, 1.75 mm diameter, 750 g spool, recyclable and low-odour

  • ColorBlack
  • TypeFilament
  • Easy printing with no unpleasant fumes or odours
  • Strong, tough material with a naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Pairs with Scaffold support for reliable adhesion and clean breakaway
  • Recyclable PETG-based filament in 1.75 mm diameter, 750 g spool

E3D spoolWorks EDGE Filament 1.75mm

E3D spoolWorks EDGE is a PETG-based filament developed in-house for 3D printing. It combines the toughness of ABS with the ease of use associated with PLA. The material delivers strong, stiff parts with exceptional layer adhesion and very low warping. Supplied as a 750g spool in Very Black30 colour.

Thermals noise and power draw

As a printing filament this product has no thermals, noise or power draw of its own. Normal use involves heating the material through your printer’s hotend at standard PETG-type temperatures. The formulation prints with no unpleasant fumes or odours. Power consumption and acoustics depend entirely on the printer hardware.

Build fit and requirements

The 1.75mm diameter suits the majority of desktop extruders. Bed adhesion works effectively with just a small amount of gluestick. Edge pairs with E3D Scaffold support material for clean breakaway supports. It is widely recyclable. Buyers who need a different diameter or a non-PETG material will not be served by this spool.

Prednosti

  • Easy printing with no unpleasant fumes or odours
  • Strong, tough material with a naturally glossy finish
  • Adheres to bed surfaces using only a little gluestick
  • Pairs with Scaffold support for reliable adhesion and clean breakaway
  • Recyclable PETG-based filament in 1.75 mm diameter, 750 g spool

Špecifikácie

BrandE3D
ModelEdge
ColorBlack
TypeFilament

Otázky k tomuto produktu

How do I load the 1.75mm filament into my printer without jamming?

Heat the hotend to the recommended printing temperature, then push the filament through until it extrudes cleanly; the step users miss is ensuring the drive gear grips without grinding the 1.75mm strand.

What maintenance will the 750g spool need over time?

Keep the Edge spool sealed with desiccant when not printing; if the material absorbs moisture, dry it before use to restore the easy-print, no-odour behaviour.

What limit appears first during a long print with this Edge filament?

Warp is nearly eliminated by the super-low contraction, so the first practical limit is the 750g spool running out on very large parts.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.