Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Eight black brass compression fittings with diamond-textured grip rings for 10x16mm soft tubing

FormulaMod

FormulaMod 10x16mm G1/4 Compression Fittings 8 Pack Black

SKU CH-RD2G-QCZH0

Set of eight G1/4 compression fittings for 10x16mm soft tubing, machined from H59 brass with a diamond-textured grip

  • TypeFittings
  • H59 brass resists corrosion in liquid loops
  • 10 mm ID × 16 mm OD soft-tube compatibility
  • G1/4 thread fits standard water-cooling components
  • Diamond-knurled body prevents slipping during installation
  • Eight fittings included for multi-block builds

Precision G1/4 fittings for 10x16 mm tubing

These eight compression fittings are machined from H59 brass and accept 10x16 mm (3/8" ID x 5/8" OD) soft tube. The G1/4 thread matches standard water-cooling ports and each fitting carries a diamond-textured collar for extra grip during assembly. One pack supplies enough connectors for a typical dual-radiator loop.

Builders using 10x16 mm soft tube

This kit suits anyone plumbing a custom loop with 10x16 mm soft tube and G1/4 ports. It will not work with hard tube, push-fit connectors or tubing sizes other than 10x16 mm.

Brass construction holds seal under pressure

The H59 brass bodies resist corrosion and maintain clamping force during prolonged thermal cycling. Diamond knurling prevents collar loosening when tubing expands from coolant heat. Eight fittings stay secure throughout extended load sessions.

Prednosti

  • H59 brass resists corrosion in liquid loops
  • 10 mm ID × 16 mm OD soft-tube compatibility
  • G1/4 thread fits standard water-cooling components
  • Diamond-knurled body prevents slipping during installation
  • Eight fittings included for multi-block builds

Špecifikácie

TypeFittings

Otázky k tomuto produktu

Does my loop already use 10x16mm soft tubing and G1/4 threaded ports for these fittings to seal correctly?

Yes — the compression design is made for 10x16mm (3/8"IDx5/8"OD) soft tube and standard G1/4 threads found on most water blocks, radiators and reservoirs.

Will the G1/4 threads on these black fittings mate with older brass or nickel blocks that also use G1/4 ports?

G1/4 is an industry-standard thread pitch, so the H59 brass bodies screw into any legacy component with a G1/4 female port without adapters.

How can I confirm each of the eight fittings is seated and leak-free after assembly?

Tighten the compression collar until the diamond-textured grip bites the tube, then run the loop under pressure and watch for zero drips at every joint.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.