Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Spool of white water-soluble 1.75mm filament, 0.75kg

Lay Filaments

Lay Filaments Lay-Cloud Dissolvable Support Filament 1.75mm 0.75kg

SKU CH-N90A-3NG1R

Water-soluble support filament for flexible 3D prints, dissolves in cold or hot water without damaging the model

  • Water-soluble support dissolves in cold or hot water without residue
  • Works with flexible filaments such as NinjaFlex TPE and semi-flexible materials
  • Removes cleanly without damaging the final printed piece
  • Tight diameter tolerance of ± 0.1 mm for consistent extrusion
  • Prints at 230-240 °C on a 1.75 mm spool weighing 0.75 kg

Dissolvable support for flexible filaments

Lay-Cloud is a water-soluble support filament created for dual-extrusion printing alongside flexible or semi-flexible materials such as TPE. It dissolves completely in cold or hot water after the print finishes, leaving no residue on the final part. The formulation targets makers who need reliable supports without damaging delicate flexible structures.

Precise 1.75 mm diameter with tight tolerance

The filament holds a diameter tolerance of ± 0.1 mm for consistent feeding through a Bowden or direct-drive extruder. Each spool contains 0.75 kg of material wound for standard 3D printer spool holders. No heated bed is required, simplifying printer setup for support-only printing.

Prints at 230 to 240 °C with water-based removal

Normal extrusion temperatures sit between 230 and 240 °C, keeping power draw comparable to common engineering filaments. Once the model is complete, submerging it in water dissolves the support structure over a few hours; warmer water speeds the process. The material is not suited for single-extruder workflows or for use with rigid plastics that do not require soluble supports.

Prednosti

  • Water-soluble support dissolves in cold or hot water without residue
  • Works with flexible filaments such as NinjaFlex TPE and semi-flexible materials
  • Removes cleanly without damaging the final printed piece
  • Tight diameter tolerance of ± 0.1 mm for consistent extrusion
  • Prints at 230-240 °C on a 1.75 mm spool weighing 0.75 kg

Špecifikácie

BrandLay Filaments

Otázky k tomuto produktu

What printing temperature range does the 1.75 mm Lay-Cloud filament require?

The filament prints at 230-240 degC and has a diameter tolerance of ± .1 mm for consistent extrusion.

What spool weight and filament diameter does this Lay-Cloud support material come in?

It is supplied as a .75 kg spool of 1.75 mm water-soluble filament in the Lay-Away series.

How do you remove Lay-Cloud supports after printing flexible parts?

Submerge the finished print in cold or hot water for a few hours; the support dissolves completely without damaging the flexible model.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.