Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Compact rectangular ASIC miner in matte grey metal with front grille, rear dual 6-pin power ports and Goldshell branding

Goldshell

Goldshell Mini Doge 3 700M/550M Dual Mode mining hardware

SKU CH-0732-83JC3

A dual-mode ASIC miner for Dogecoin and Litecoin delivering 700 Mh/s at 400 W or 550 Mh/s at 260 W

  • Dual-mode ASIC delivers 700Mh/s at 400W for strong Dogecoin and Litecoin earnings
  • Low-power mode runs at 550Mh/s using only 260W to cut electricity costs
  • Compact bare-bone chassis fits tight spaces without extra rack hardware
  • Two mandatory 6-pin power inputs ensure stable current delivery under full load
  • Purpose-built for Scrypt coins so no algorithm switching or firmware hassles

Dual-mode Scrypt ASIC for LTC and DOGE

The Goldshell Mini Doge 3 is an ASIC miner built for the Scrypt algorithm used by Litecoin and Dogecoin. It targets hobbyist and small-scale operators who want a compact unit that can run at two distinct performance points without changing hardware.

High and low power profiles replace single-speed

The default profile delivers 700Mh/s at 400W while the low-power profile drops to 550Mh/s at 260W. Switching between them lets the operator match electricity cost or thermal headroom without buying a second device, making the jump worthwhile when power rates vary by time of day or season.

Two 6-pin power inputs set the hard wiring limit

Both 6-pin connectors must be fully seated before the miner is powered on; running on a single connector is not supported. This dual-connector requirement defines the minimum cabling and power-supply layout the builder must provide.

Poudarki

  • Dual-mode ASIC delivers 700Mh/s at 400W for strong Dogecoin and Litecoin earnings
  • Low-power mode runs at 550Mh/s using only 260W to cut electricity costs
  • Compact bare-bone chassis fits tight spaces without extra rack hardware
  • Two mandatory 6-pin power inputs ensure stable current delivery under full load
  • Purpose-built for Scrypt coins so no algorithm switching or firmware hassles

Specifikacije

Za ta izdelek še ni objavljenih specifikacij.

Vprašanja o tem izdelku

What are the power connector requirements for the Goldshell Mini Doge 3?

The miner requires two 6PIN power interfaces to be fully connected. Operating with only one 6PIN plugged in is not supported and must be avoided.

What is the correct installation step for the dual 6PIN power interfaces on this miner?

Before powering on, verify that both 6PIN connectors are completely seated. The unit will not operate correctly if only a single 6PIN interface is used.

Which components on the Goldshell Mini Doge 3 are most likely to need replacement over time?

The internal cooling fans are the primary moving parts and will typically require replacement after extended continuous operation at 400W or 260W power draw.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.