Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Three green ESP32 expansion boards with 38-pin headers and USB-C connectors

KEHIPI

KEHIPI 3PCS 38PINS ESP32 Development Board Type-C CP2102

SKU CH-6P0E-S6YPH

Three ESP32 expansion boards with 38-pin headers and Type-C CP2102 interfaces for compatible WROOM and WROVER modules

  • 3-pack gives spare boards for parallel projects
  • 38-pin layout matches wide ESP32 modules like WROOM-32D and WROVER
  • USB Type-C port with CP2102 bridge for simple flashing and power
  • Supports Lua, FreeRTOS and LWIP for rapid IoT firmware development
  • Works in AP, STA and AP+STA modes for flexible Wi-Fi networking

38-Pin ESP32 Expansion Board Pack

This pack contains three 38-pin expansion boards built for ESP32 development modules. Each board uses a CP2102 USB-to-UART bridge and offers a Type-C or Micro USB interface. The extended bottom-board layout matches the ESP32-DevKitC-32 form factor and supports Lua programming with LWIP and FreeRTOS in AP, STA and AP+STA modes.

Makers needing multiple ESP32 breakout boards

Suited for developers who want three ready-to-use 38-pin carrier boards for rapid prototyping or classroom sets. Not for buyers who need a different pin count, a single-unit pack, or an on-board ESP32 module included in the package.

38-pin compatibility constraint

The boards only accept the listed 38-pin wide-version modules such as ESP32-WROOM-32S, 32E, 32D, 32U, WROVER and WROVER-IB. Verify your module against the approved ASINs B09LMBX8WH, B09KRHNC6Z, B08HMJ1X6W, B088QVQCTL and B086YS4Z3F before ordering.

Poudarki

  • 3-pack gives spare boards for parallel projects
  • 38-pin layout matches wide ESP32 modules like WROOM-32D and WROVER
  • USB Type-C port with CP2102 bridge for simple flashing and power
  • Supports Lua, FreeRTOS and LWIP for rapid IoT firmware development
  • Works in AP, STA and AP+STA modes for flexible Wi-Fi networking

Specifikacije

BrandAITRIP

Vprašanja o tem izdelku

What module pin count does this 38-pin expansion board require?

The board only accepts ESP32 modules with a 38-pin wide footprint such as the WROOM-32D, WROOM-32U or WROVER variants listed in the compatibility notice.

How do I connect the board to a computer for programming?

Plug a USB Type-C cable into the on-board CP2102 USB-to-UART bridge; the board then appears as a serial port for flashing firmware.

When should I replace the CP2102 USB-to-UART bridge on this board?

Replace it only if the device no longer enumerates as a COM port or shows persistent upload failures across multiple cables and hosts.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.