Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in
Four clear acrylic tubes bent at 90 degrees with 110mm and 415mm straight sections, 14mm outer diameter

Bitspower

Bitspower Pre-bent 90° Acrylic Hard Tube OD14mm 110x415mm 4-pack

SKU CH-YJ9R-3X8FY

Four pre-bent 90-degree acrylic tubes with 14 mm outer diameter and 110 mm by 415 mm straight sections simplify custom water-cooling builds

  • TypeLiquid Cooling System
  • Pre-bent 90° curve removes the need for manual tube bending
  • Acrylic hard tube construction provides rigid leak-resistant coolant paths
  • 14 mm outer diameter fits standard compression fittings
  • 110 mm and 415 mm straight sections allow custom trimming
  • Four tubes included to complete multiple loop runs

Pre-bent 90° acrylic tubes for custom loops

This four-pack of Bitspower pre-bent hard tubes gives builders ready-made 90-degree corners in clear acrylic. Each piece includes straight sections of 110mm and 415mm on either side of the bend. The tubes arrive at the outer diameter required for standard OD14mm fittings. Novices and experienced builders alike can skip the heating and bending step entirely.

Acrylic construction with OD14mm compatibility

The rigid acrylic material holds its shape without kinking and resists clouding over time. Because the 90-degree curves are factory-formed, alignment between components is more predictable than with hand-bent runs. Builders simply measure, cut the straight sections to length, and press the ends into their chosen OD14mm compression or push-fit fittings. No specialised bending tools or silicone inserts are needed.

Replaces hand-bent tubing in new builds

This set suits anyone assembling a custom water-cooling loop who wants to avoid the trial-and-error of bending acrylic themselves. It is not for builders who need curves other than 90 degrees or who prefer the flexibility of soft tubing. The fixed bend angle and straight-leg lengths determine the routing possibilities, so plan your component layout before committing.

I korthet

  • Pre-bent 90° curve removes the need for manual tube bending
  • Acrylic hard tube construction provides rigid leak-resistant coolant paths
  • 14 mm outer diameter fits standard compression fittings
  • 110 mm and 415 mm straight sections allow custom trimming
  • Four tubes included to complete multiple loop runs

Specifikationer

TypeLiquid Cooling System

Frågor om den här produkten

What outer diameter does the 14 mm acrylic tube match for fittings?

The tube has a 14 mm outer diameter, so it fits standard 14 mm OD compression fittings used in custom loops.

How much straight length remains on each side of the 90° bend after the pre-bent curve?

Each piece provides 110 mm on one leg and 415 mm on the other, giving two distinct straight sections to trim to final size.

Do I need a heat gun to install these pre-bent tubes, or can I push them straight onto fittings?

No heat gun is required; simply cut the 110 mm and 415 mm legs to length, chamfer the ends, and press them into 14 mm OD fittings.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.