Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in
Set of four brass nozzles for AD5X printer, diameters 0.25 0.4 0.6 0.8

Flashforge

Flashforge Nozzle Assembly AD5X 300C 0.25 0.4 0.6 0.8 3d printers accessory

SKU CH-MCPY-NFKK3

Quick-swap nozzle set for AD5X printers with .25, .4, .6 and .8 mm tips rated to 300 °C

Size 0.25+0.4+0.6+0.8

  • Minimal downtime with heating to temperature in under a minute
  • High-temperature resistance up to 300 °C for advanced filaments
  • Quick-release design reduces maintenance time and keeps print quality stable
  • Four nozzle diameters — .25 .4 .6 .8 — for detail or speed
  • Precision-engineered for seamless integration with the AD5X printer

AD5X Nozzle Assembly

This Flashforge nozzle assembly is designed for the AD5X 3D printer and ships as a set of four interchangeable nozzles with diameters of .25, .4, .6 and .8 millimetres. The quick-release mechanism allows fast swaps without tools, while the 300C temperature rating supports high-temperature filaments. It is aimed at makers who need to change nozzle sizes regularly for different print jobs.

Upgrade from single nozzles

Replacing a fixed single-diameter nozzle with this set removes the need to disassemble the hot end each time a different resolution or flow rate is required. The rapid heating capability brings the nozzle to printing temperature in under a minute, so the switch adds minimal downtime. The jump is worth it when a project demands both fine detail and high-volume extrusion in the same session.

Suits multi-material workflows

Users printing with abrasive or high-temperature materials benefit from the hardened construction and 300C ceiling, while the quick-release design keeps maintenance intervals short. Builders who only ever use a single nozzle size or who operate printers other than the AD5X will not gain the integration advantages this kit provides.

I korthet

  • Minimal downtime with heating to temperature in under a minute
  • High-temperature resistance up to 300 °C for advanced filaments
  • Quick-release design reduces maintenance time and keeps print quality stable
  • Four nozzle diameters — .25 .4 .6 .8 — for detail or speed
  • Precision-engineered for seamless integration with the AD5X printer

Specifikationer

BrandFlashforge

Andra versioner av den här modellen

4 till i samma serie

Samma familj, men olika minne, kylning eller klockfrekvens — jämför innan du bestämmer dig.

Frågor om den här produkten

Which nozzle diameters are included in the AD5X assembly?

The assembly includes 0.25, 0.4, 0.6 and 0.8 mm nozzles for the AD5X printer.

How is the quick-release nozzle swapped on the AD5X?

The quick-release mechanism lets you remove and install the nozzle by hand without tools; the step often missed is ensuring the nozzle seats fully before tightening the latch.

When should the AD5X nozzle be replaced?

Replace the nozzle when print quality drops, filament jams increase, or the tip shows visible wear from abrasive filaments at 300C.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.