NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.
JacobsParts Inc.
Adjustable step-up converter raises 4–32 V input to a regulated 5–35 V output at up to 2 A and 20 W with 94 % peak efficiency
The JacobsParts XL6009 module converts a lower DC input into a higher regulated output for electronics projects. It accepts 4 to 32 volts input and delivers 5 to 35 volts at up to 2 amps. The board suits hobbyists and engineers building custom power rails from batteries or automotive sources. Output must always exceed input voltage.
The integrated XL6009 IC includes over-temperature and over-current protection for continuous operation. Efficiency reaches up to 94 percent depending on the voltage differential between input and output. Switching runs at 400 kilohertz with output ripple below 50 millivolts and load regulation within 0.5 percent. The potentiometer may require up to 15 turns before the output voltage begins to change.
The PCB-mount form factor measures 40 by 20 by 12 millimetres and handles a maximum of 20 watts. Constant-voltage regulation makes it suitable for LED strips and modules but not for driving raw LEDs directly. Input range stops at 32 volts and output caps at 35 volts, so designs needing higher boost ratios fall outside the device capability.
| Brand | JacobsParts |
|---|---|
| Model | DCMOD-T |
| Type | Step-Up Voltage Regulator |
| Mounting Style | PCB Mount |
| Current Rating | 2 A |
| Power Rating | 20 W |
The XL6009 IC includes over-temperature protection and an integrated MOSFET. At up to 94% efficiency, only a small fraction of the 20 W maximum becomes heat. There are no moving parts, so the module is completely silent in operation.
You need a DC source between 4 V and 32 V — for example a 3.7 V lithium cell or a 12 V battery — plus a multimeter to set the potentiometer, which may require up to 15 turns before the output voltage changes.
The module operates at 400 kHz with output ripple below 50 mV. Sensitive analog circuits on the same rail may pick up switching noise, so add decoupling capacitors or a separate linear regulator for those legacy devices.
Även i den här avdelningen
Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.
Det du betalar med, och det du ser priserna i.
Skickas från din plånbok i kassan
Endast visning — katalogen är prissatt i US-dollar
Ingen valuta matchar.
Välj det språk du vill att webbplatsen ska visas på.
Ny här?
Har du redan ett konto?
Det finns ingen automatisk återställning: den här butiken skickar inga e-postmeddelanden, så det finns ingen engångslänk att begära. Lämna adressen kopplad till kontot, så hanteras den för hand.
Förfrågan noterad
Inget är på väg till din inkorg — den här butiken skickar aldrig e-post. Någon tar hand om detta manuellt.
Kom du på det?