NEMIX RAM
NEMIX RAM 32GB DDR4 2933MHz CL21 ECC SODIMM memory upgrade
32GB DDR4 2933MHz ECC SODIMM module with CL21 latency and 1.2V operation, validated for Supermicro X12SCV motherboards
- Capacity32GB
- Type260-Pin DDR4 ECC SODIMM
- SpeedDDR4 2933 (PC4 23400)
- CAS LatencyCL21
- Voltage1.20V
- ECCYes
- 32 GB capacity expands system memory for demanding workloads
- DDR4 2933 MHz speed delivers high data throughput for responsive performance
- ECC error correction detects and corrects single-bit errors to protect data integrity
- 260-pin SODIMM form factor fits Supermicro X12SCV motherboards exactly
- 2 V operation reduces power draw and heat output
Exact-match DDR4 ECC SODIMM
This 32 GB DDR4 2933 MHz module is built as an exact-match upgrade for Supermicro X12SCV-W and X12SCV-LVDS motherboards. It delivers 2Rx8 unbuffered ECC operation at 1.2 V with CL21 timing so the memory controller recognises the full capacity at rated speed. The 260-pin SODIMM form factor fits the slots these boards require.
Straightforward SODIMM install
Installation follows the standard SODIMM procedure: power down, open the chassis, align the notch on the 260-pin module with the slot key, insert at the correct angle and press until the retention clips engage. The most common issues are mismatched population order or exceeding the board's supported capacity per slot, which prevent the system from posting.
Verify board limits first
Check your motherboard manual for the maximum supported capacity per slot, approved population sequence and any BIOS version requirements before ordering. This module uses DDR4 ECC unbuffered SODIMM technology only; it will not fit UDIMM or RDIMM slots and is not compatible with systems that require registered memory or a different DDR generation.
I korthet
- 32 GB capacity expands system memory for demanding workloads
- DDR4 2933 MHz speed delivers high data throughput for responsive performance
- ECC error correction detects and corrects single-bit errors to protect data integrity
- 260-pin SODIMM form factor fits Supermicro X12SCV motherboards exactly
- 2 V operation reduces power draw and heat output
Specifikationer
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Memory |
| Model | DDR4 ECC Unbuffered SODIMM Memory |
| Part Number | MSE23400-328K1 |
| Capacity | 32GB |
| Type | 260-Pin DDR4 ECC SODIMM |
| Speed | DDR4 2933 (PC4 23400) |
| CAS Latency | CL21 |
| Voltage | 1.20V |
| ECC | Yes |
| Buffered/Registered | Unbuffered |
| Rank | 2Rx8 |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Heat Spreader | No |
| Compatible System | Supermicro |
| Features | DDR4 ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 32GB DDR4 2933MHz PC4-23400 2Rx8 1.2V 260-PIN ECC SODIMM KIT |
Frågor om den här produkten
How can I confirm the 32GB DDR4 2933MHz CL21 ECC SODIMM is running at its rated speed after installation?
Enter the system BIOS or UEFI and verify the memory frequency reads 2933MHz (PC4-23400) with CL21 timings at 1.2V; the POST screen should also show the full 32GB capacity and ECC status as active.
What comes in the package and is anything else needed for the Supermicro X12SCV-W motherboard?
The box contains one 32GB 260-pin DDR4 ECC Unbuffered SODIMM module (part MSE23400-328K1); no additional parts or cables are required for installation on the compatible Supermicro boards.
Which version should I choose if my Supermicro board only supports 1.2V DDR4 2933MHz ECC SODIMMs?
This exact module matches that specification — 32GB, 2933MHz, CL21, 1.2V, 2Rx8, 260-pin ECC Unbuffered — so it is the correct version for that voltage and speed requirement.
Även i den här avdelningen
Andra har jämfört dessa
Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.



