Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in
Green circuit board with black memory chips, gold edge connector, thin rectangular SODIMM module

OWC

OWC 4GB DDR3 1600 CL11 204-pin SODIMM for HP Envy TouchSmart 23

SKU CH-EACA-846EZ

A 4 GB DDR3 1600 MHz SODIMM upgrade for HP Envy TouchSmart 23 series all-in-one PCs

  • Capacity4GB
  • Type204-Pin DDR3 Non-ECC SODIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • 4GB DDR3 upgrade boosts multitasking on HP Envy TouchSmart 23
  • JEDEC-standard PC3-12800 CL11 module ensures warranty-safe compatibility
  • 1600MHz DDR3 speed improves system responsiveness for daily tasks
  • Single 204-pin SODIMM installs easily in supported HP all-in-one desktops
  • 5V non-ECC unbuffered design matches factory memory specifications

HP Envy TouchSmart 23 DDR3 upgrade

This 4 GB DDR3 1600 SODIMM is built specifically for the HP Envy TouchSmart 23 series. It delivers a single unbuffered 1Rx8 module that installs directly into the 204-pin slot. The 1.5 V non-ECC design matches the original factory specification for a warranty-safe improvement.

DDR3 1600 SODIMM interface limits

The PC3-12800 CL11 rating sets the maximum bandwidth and latency for this generation of memory. DDR3 architecture caps transfer rates at 1600 MT/s and requires 1.5 V operation, so newer platforms using different voltages or keying will not accept this module. Systems already running at the chipset ceiling will not gain extra speed from this part.

Replacing factory DDR3 in the Envy 23

Swapping the original memory for this 4 GB stick raises total capacity when the board has a free slot or supports a larger single module. The jump is worth it if the current configuration leaves headroom for more RAM and the workload demands extra space for multitasking. Buyers whose TouchSmart 23 already uses the maximum supported density or runs a different memory generation will not benefit.

I korthet

  • 4GB DDR3 upgrade boosts multitasking on HP Envy TouchSmart 23
  • JEDEC-standard PC3-12800 CL11 module ensures warranty-safe compatibility
  • 1600MHz DDR3 speed improves system responsiveness for daily tasks
  • Single 204-pin SODIMM installs easily in supported HP all-in-one desktops
  • 5V non-ECC unbuffered design matches factory memory specifications

Specifikationer

BrandOWC
Part Number1S6D31R804GB
Capacity4GB
Type204-Pin DDR3 Non-ECC SODIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP ENVY TouchSmart 23 Series using DDR3 Memory

Andra versioner av den här modellen

5 till i samma serie

Samma familj, men olika minne, kylning eller klockfrekvens — jämför innan du bestämmer dig.

Frågor om den här produkten

Should I choose the 4 GB module or add a second stick for 8 GB total?

This listing is a single 4 GB SODIMM. The Envy TouchSmart 23 has two DDR3 slots, so adding a second identical module will give 8 GB in dual-channel mode.

What does the 1600 MT/s speed mean once the module is installed?

The system will run the memory at DDR3-1600 with CL11 timing, delivering the standard PC3-12800 bandwidth for everyday tasks and multitasking.

Is the 204-pin DDR3 SODIMM interface compatible with my Envy TouchSmart 23?

Yes — the module is a 204-pin DDR3 SODIMM at 1.5 V, which matches the Envy TouchSmart 23 DDR3 memory slots exactly.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.