Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in
Small square black 85mm 4-pin VGA cooling fan with transparent blades

Vszerda

Vszerda PLD09210S12HH 85mm 4-pin VGA cooling fan for RTX 3060 3070 3080 3090 Ventus 3X

SKU CH-XV5M-MER90 MPN PLD09210S12HH

85 mm 4-pin replacement fan cools MSI Ventus 3X models from RTX 3060 to 3090 with 40 mm mounting centres

  • Direct-fit replacement for Ventus 3X models including RTX 3060 3070 3080 3090
  • 4-pin PWM header enables precise speed control from the graphics card
  • 12 V 0.40 A motor delivers reliable airflow for thermal management
  • Compact 85 mm square frame with 13 mm thickness fits tight cooler shrouds
  • Mounting holes spaced 40 mm centre-to-centre match original fan layout

Replacement fan for Ventus 3X cards

This 85 mm 4-pin VGA cooling fan is built for MSI GeForce RTX 3060, 3060 Ti, 3070, 3070 Ti, 3080, 3080 Ti and 3090 Ventus 3X models. It suits owners of those specific cards who need a direct swap for a worn or noisy original cooler. The part is sold new and ready to install.

No screws or heatsink included

The package contains only the fan assembly itself. Mounting hardware, thermal pads and the heatsink are not supplied, so buyers must reuse existing fixings or source them separately. This keeps the cost down for workshops that already have spare screws on hand.

40 mm mounting-hole spacing decides fit

Hole centres measure 40 mm in a square pattern; the frame is 85 mm by 85 mm by 13 mm thick. Verify these dimensions against the original fan before ordering, because the same GPU model can ship with different fan layouts. Mismatched spacing will prevent installation.

I korthet

  • Direct-fit replacement for Ventus 3X models including RTX 3060 3070 3080 3090
  • 4-pin PWM header enables precise speed control from the graphics card
  • 12 V 0.40 A motor delivers reliable airflow for thermal management
  • Compact 85 mm square frame with 13 mm thickness fits tight cooler shrouds
  • Mounting holes spaced 40 mm centre-to-centre match original fan layout

Specifikationer

Inga publicerade specifikationer för den här produkten än.

Frågor om den här produkten

Will the PLD09210S12HH fan need periodic bearing lubrication or full replacement after extended use?

The sleeve-bearing design is sealed for life; no lubrication is possible. Plan to replace the fan if rpm drops or noise rises after several years of continuous operation.

What thermal or electrical limit appears first when the RTX 3080 Ventus 3X runs at full load for hours?

The 0.40 A / 12 V rating caps the fan at its factory speed curve; the GPU’s own thermal throttle point will be reached before the fan hits an electrical limit.

How much noise and heat does the 85 mm 4-pin cooler add inside the Ventus 3X shroud during all-day gaming?

At 12 V the fan draws 0.40 A, moving air through the 85 mm frame with a low-profile 13 mm thickness that keeps acoustic output and exhaust heat modest.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.