Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Clear nylon inserts for 13mm OD PETG tubing

Alphacool

Alphacool Eiszapfen Pro 13mm OD PETG Tubing Inserts (17565)

SKU CH-4Z9V-H2XF2

Nylon inserts and O-rings secure 13 mm OD PETG hard tubing inside Eiszapfen Pro fittings against heat deformation

  • TypeTubing
  • Replacement O-rings maintain a tight seal on 13mm OD HardTube fittings
  • Nylon inserts prevent PETG tube deformation caused by heat and compression
  • Inserts protect against leaks at GPU and CPU outlets where temperatures run highest
  • Spare-parts kit restores original fitting performance for Eiszapfen Pro connectors
  • Designed specifically for 13mm OD PETG HardTube, not compatible with Bitspower tubing

Alphacool Eiszapfen Pro 13mm OD Inserts

These replacement O-rings and nylon inserts are made for Alphacool Eiszapfen Pro fittings that use 13mm OD hard tubing. They provide the sealing components needed to maintain a watertight connection in a custom liquid-cooling loop. The parts are sold new under article number 17565.

Suited for builders using PETG hard tubes

The nylon inserts stop PETG tubing from deforming under heat and compression, which can otherwise cause leaks at GPU or CPU outlets. This kit is not intended for acrylic tubing, which does not need the inserts, nor for Bitspower brand tubing, where fitment is not recommended.

Kit contains O-rings and nylon inserts for 13mm OD

The wide O-ring seals the tube inside the fitting while the insert supports the PETG wall against softening at higher coolant temperatures. Without the insert, PETG can collapse at restriction points and break the seal. Acrylic hard tubes do not require the insert, so this kit adds no benefit there.

Přednosti

  • Replacement O-rings maintain a tight seal on 13mm OD HardTube fittings
  • Nylon inserts prevent PETG tube deformation caused by heat and compression
  • Inserts protect against leaks at GPU and CPU outlets where temperatures run highest
  • Spare-parts kit restores original fitting performance for Eiszapfen Pro connectors
  • Designed specifically for 13mm OD PETG HardTube, not compatible with Bitspower tubing

Specifikace

TypeTubing

Otázky k tomuto produktu

Will these inserts fit my existing Alphacool Eiszapfen Pro fittings for 13mm OD hard tubing?

Yes, they are made specifically for Alphacool Eiszapfen Pro fittings sized for 13mm OD HardTube.

Do I need these nylon inserts if I am reusing PETG tubing instead of acrylic?

Yes, PETG is softer than acrylic and can deform under heat and compression; the inserts prevent that deformation inside the fitting.

How can I confirm the inserts are seated correctly after assembly?

The wide O-ring sits inside the fitting body and the nylon insert sits within the tubing; a leak-free loop under pressure confirms correct seating.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.