Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Two green circuit boards with black chips, no heat spreader, SODIMM form factor

NEMIX RAM

NEMIX RAM 16GB (2x8GB) DDR5 5600 CL46 SODIMM memory upgrade for Supermicro X14SAV-F

SKU CH-CMJN-C2G19

16 GB dual-channel DDR5 SODIMM kit running at 5600 MT/s with CL46 latency for the Supermicro X14SAV-F

  • Capacity16GB (2 x 8GB)
  • Type262-Pin DDR5 SODIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 16GB 2X8GB

  • Exact-match DDR5-5600 kit runs at rated speed
  • Verified fit for Supermicro X14SAV-F motherboard
  • Major OEM chips tested for stability at CL46
  • 262-pin SODIMM form factor matches system requirements
  • 16 GB dual-channel capacity with 1.1 V operation

16GB DDR5 SODIMM kit for Supermicro X14SAV-F

This 16GB kit contains two 8GB DDR5 5600 modules built to the exact 262-pin SODIMM form factor required by the Supermicro X14SAV-F motherboard. The 1Rx8 Non-ECC Unbuffered design matches the board's memory controller expectations for full-capacity recognition and rated-speed operation. Major OEM chips from Samsung Micron or Hynix provide tested stability at the specified timing and voltage.

Thermals noise and power at 1.1V

Operating at 1.10V the modules draw minimal power and generate low heat without a heat spreader. The Unbuffered Non-ECC design keeps electrical load light on the memory controller. Silent passive cooling suits compact laptop and small-form-factor chassis where fan noise must stay low.

CL46 timing at DDR5 5600 decides fit

The CL46 CAS latency at DDR5 5600 (PC5-44800) is the single specification that determines whether this kit runs at its rated speed on the X14SAV-F. If your system manual requires a different latency or voltage the modules may downclock or fail to post. Builders needing ECC registered DIMMs or a different pin count cannot use this kit.

Přednosti

  • Exact-match DDR5-5600 kit runs at rated speed
  • Verified fit for Supermicro X14SAV-F motherboard
  • Major OEM chips tested for stability at CL46
  • 262-pin SODIMM form factor matches system requirements
  • 16 GB dual-channel capacity with 1.1 V operation

Specifikace

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered SODIMM Memory
Part NumberMS44800-818K2
Capacity16GB (2 x 8GB)
Type262-Pin DDR5 SODIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content16GB 2X8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 262-PIN Non-ECC SODIMM KIT

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

How do I install the 262-pin DDR5 SODIMM modules in the Supermicro X14SAV-F, and which slot order should I follow?

Power off the system, open the chassis, align each module's notch with the slot key, insert at a slight angle until the gold contacts are hidden, then press down until the side clips click. Check the board manual for the approved population order before seating both 8 GB sticks.

What maintenance or replacement will the 1Rx8 non-ECC SODIMM kit need over time?

No scheduled maintenance is required. Keep the motherboard firmware current so the memory controller continues to initialise the 5600 MT/s CL46 timings at 1.10 V. If a module ever fails, the lifetime replacement warranty covers a swap.

What limit appears first when the 16 GB DDR5-5600 kit runs sustained workloads?

The memory controller's thermal throttle point is reached before the modules themselves, since the sticks have no heat spreader and operate at the standard 1.10 V JEDEC voltage. Adequate chassis airflow prevents early throttling.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.