Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Two green circuit boards with black memory chips and gold edge connectors side by side

NEMIX RAM

NEMIX RAM DDR5-5600 ECC UDIMM 96GB (2×48GB) CL46 1.1V memory upgrade

SKU CH-J6D4-C4DFG

96GB kit of two 48GB DDR5 ECC UDIMM modules running at 5600MHz with CL46 latency and 1.1V operation

  • Capacity96GB (2 x 48GB)
  • Type288-Pin DDR5 ECC UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 96GB 2X48GB

  • 96 GB capacity from two 48 GB modules for high-density workloads
  • DDR5 5600 speed rated at PC5-44800 for fast data throughput
  • ECC protection detects and corrects single-bit errors on the fly
  • CL46 latency at 1.1 V for stable JEDEC operation
  • 288-pin UDIMM form factor matches Supermicro X14SAZ-TLN4F motherboard requirements

Exact-Match DDR5 ECC Kit

This 96 GB kit delivers two 48 GB DDR5-5600 modules built to the precise rank, voltage and timing the Supermicro X14SAZ-TLN4F expects. ECC protection corrects single-bit errors on the fly to prevent silent data corruption in critical workloads. The unbuffered 288-pin UDIMM form factor matches the board's memory-population rules without requiring registered DIMMs. It is not suited for systems that only accept RDIMM or SODIMM modules.

Build Integration Requirements

Installation requires a motherboard with DDR5 UDIMM slots that support 5600 MT/s PC5-44800 operation at 1.1 V and a 2Rx8 rank configuration. The kit frees the memory controller from training mismatches by matching the exact specifications the firmware validates at POST. Builders must still consult the system manual for approved DIMM population order and maximum supported capacity before fitting the modules.

Sustained Load Behaviour

Under continuous operation the modules maintain their rated DDR5-5600 speed and CL46 latency at the standard 1.1 V without needing additional voltage headroom. ECC circuitry continuously monitors and corrects single-bit errors, keeping data integrity intact during long compute runs. The absence of a heat spreader means adequate chassis airflow is required to keep temperatures stable over extended periods.

Přednosti

  • 96 GB capacity from two 48 GB modules for high-density workloads
  • DDR5 5600 speed rated at PC5-44800 for fast data throughput
  • ECC protection detects and corrects single-bit errors on the fly
  • CL46 latency at 1.1 V for stable JEDEC operation
  • 288-pin UDIMM form factor matches Supermicro X14SAZ-TLN4F motherboard requirements

Specifikace

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 ECC Unbuffered UDIMM Memory
Part NumberME44800-4828K2
Capacity96GB (2 x 48GB)
Type288-Pin DDR5 ECC UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC Unbuffered UDIMM Motherboard Compatible
Package Content96GB 2X48GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN ECC UDIMM KIT

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

Will the 1.1V DDR5-5600 modules stay stable during continuous all-day workloads?

The kit runs at 1.1V with CL46 timing, the exact voltage and latency the memory controller expects, so sustained operation remains stable at the rated 5600 MT/s speed.

How much heat and noise do the bare 288-pin UDIMMs add to a fully loaded Supermicro X14SAZ-TLN4F?

The modules have no heat spreader and draw only 1.1V, so they add minimal thermal load and zero acoustic noise; system fan curves handle the small extra heat.

What motherboard slot layout and firmware support do I need for this 2Rx8 96GB ECC kit to be recognised?

A Supermicro X14SAZ-TLN4F with DDR5-5600 ECC UDIMM support, correct DIMM population order per the board manual, and a BIOS that enables ECC on unbuffered 2Rx8 modules.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.