NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.
A-Tech
4GB DDR4 2400MHz desktop DIMM module running at 1.20V for AMD and Intel systems
This 4GB DDR4 2400MHz PC4-19200 DIMM is built for desktop computers that need a straightforward memory upgrade. It fits standard 288-pin slots and runs at the JEDEC-standard 1.2V, making it a direct replacement for the Hynix HMA451U6AFR8N-UH module. The single-rank 1Rx8 layout keeps installation simple for home users and system integrators alike. Builders who need more than 4GB per slot or who require ECC error correction should look elsewhere.
The decisive specification is the tested 2400MHz frequency at 1.20V, which determines whether the module matches the motherboard's supported memory profile. If the board only accepts lower speeds or different voltages, this stick will not operate as intended. No other timing or latency figures are supplied, so compatibility rests entirely on this speed and voltage match.
Every module undergoes quality-assurance testing before it ships, which reduces the chance of early failures during installation. A lifetime warranty covers the part for as long as you own it, and US-based technical support is available before, during, and after the purchase to help with compatibility checks or troubleshooting. No additional software or accessories are bundled with the memory.
| Brand | A-Tech |
|---|---|
| Capacity | 4GB |
| Speed | DDR4 2400 (PC4 19200) |
| Tested Frequency | 2400 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Recommend Use | AMD & Intel Compatible |
The module uses the standard 288-pin DIMM form factor and runs at 1.20 V, which matches the DDR4 specification used by most desktop boards. Check your motherboard manual to confirm it supports DDR4 2400 non-ECC unbuffered memory.
Yes, provided your board has a free DDR4 DIMM slot and supports 4 GB modules. Mixing speeds is possible, but all modules will run at the speed of the slowest stick.
The product is listed as a compatible replacement for that exact Hynix part number, matching capacity, speed, voltage, and 1Rx8 organisation.
Veel samast osakonnast
Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.
See, millega maksate, ja see, milles vaatate hindu.
Saadetud teie rahakotist kassas
Ainult kuvamiseks — kataloogi hinnad on dollarites
Ükski vääring ei vasta sellele.
Valige keel, milles sait teiega räägib.
Esimest korda siin?
Teil on juba konto?
Automaatset lähtestamist ei ole: see pood ei saada ühtegi e-kirja, seega pole ka ühekordset linki, mida küsida. Jätke aadress kontole alles, seda käsitletakse käsitsi.
Päring registreeritud
Teie postkasti ei jõua midagi — see pood ei saada e-kirju üldse. Keegi tegeleb sellega käsitsi.
Tuli meelde?