NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.
A-Tech
4GB DDR4 2400MHz desktop DIMM module running at 1.20V for AMD and Intel systems
This 4GB DDR4 2400MHz PC4-19200 DIMM is built for desktop computers that need a straightforward memory upgrade. It fits standard 288-pin slots and runs at the JEDEC-standard 1.2V, making it a direct replacement for the Hynix HMA451U6AFR8N-UH module. The single-rank 1Rx8 layout keeps installation simple for home users and system integrators alike. Builders who need more than 4GB per slot or who require ECC error correction should look elsewhere.
The decisive specification is the tested 2400MHz frequency at 1.20V, which determines whether the module matches the motherboard's supported memory profile. If the board only accepts lower speeds or different voltages, this stick will not operate as intended. No other timing or latency figures are supplied, so compatibility rests entirely on this speed and voltage match.
Every module undergoes quality-assurance testing before it ships, which reduces the chance of early failures during installation. A lifetime warranty covers the part for as long as you own it, and US-based technical support is available before, during, and after the purchase to help with compatibility checks or troubleshooting. No additional software or accessories are bundled with the memory.
| Brand | A-Tech |
|---|---|
| Capacity | 4GB |
| Speed | DDR4 2400 (PC4 19200) |
| Tested Frequency | 2400 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Recommend Use | AMD & Intel Compatible |
The module uses the standard 288-pin DIMM form factor and runs at 1.20 V, which matches the DDR4 specification used by most desktop boards. Check your motherboard manual to confirm it supports DDR4 2400 non-ECC unbuffered memory.
Yes, provided your board has a free DDR4 DIMM slot and supports 4 GB modules. Mixing speeds is possible, but all modules will run at the speed of the slowest stick.
The product is listed as a compatible replacement for that exact Hynix part number, matching capacity, speed, voltage, and 1Rx8 organisation.
Også på denne hylde
Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.
Det du betaler med, og det du ser priserne i.
Sendes fra din tegnebog i kassen
Kun til visning — kataloget er prissat i USD
Ingen valuta matcher det.
Vælg det sprog, siden taler til dig på.
Ny her?
Har du allerede en?
Der findes ingen automatisk nulstilling: denne butik sender ingen e-mails, så der er intet engangslink at bede om. Efterlad adressen på kontoen, så bliver den behandlet manuelt.
Anmodning registreret
Der er intet på vej til din indbakke — denne butik sender slet ingen e-mails. Nogen behandler dem manuelt.
Kom du i tanke om den?